Part Location Diagram of 121010214 Ryobi SHORT BRACKET OUTFEED ROD
See part A-13 in the diagram

SHORT BRACKET OUTFEED ROD 121010214

Manufactured by:
Ryobi
ERP Number:
ERP18690529
Part Number:
121010214
Original Equipment Manufacturer ?
  Works with your model  RTS21!
Special Order

Easy 

30 - 60 mins 

(3 rated repairs) ?
  Works with your model   RTS21!

Troubleshooting

This part works with the following brands:
  • Ryobi
This part works with the following products:
  • Table Saw
Part# 121010214 replaces these:
0121010214,

Customer Part Reviews

?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(3 Reviews)
Click to filter by ratings:
  • 5 stars
    3
  • 4 stars
    0
  • 3 stars
    0
  • 2 stars
    0
  • 1 star
    0
  • 1
Sort by:  
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

30 - 60 mins 

(3 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

The switch burned out, and the bracket cracket due to user error

R from Nephi, Utah

3 of 3 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Parts Used:
121010214, 089110109712
The switch\'s connections were in a tight area. The good thing is that the cables are color coded to make it easy to fix. If I did it over, I would\'ve taken the cord clamps from the junction box first before I tried to do anything with the switch. (Note: the 3 screws are longer than the 4 that hold the switch in place)

Prin t out the wiring diagram in the part\'s list before you start. This will come in very handy when putting the switch back together.

Here\'s the steps should\'ve done.
1. Unscrew the 4 screws holding the switch in place. The switch can be pulled out and tested with a meter. Mine had a very strong odor of burnt parts.
2. Order new switch - easy part.
3. Tilt saw blade so you have room to work.
4. Remove the 3 screws from the cord strain relief and the green grounding wires.
5. Get come slack in the cords and slip the switch box to make it easier to hook up the switch.
6. Install the switch and connect the wires. This where the wiring diagram comes in real handy. This is the time to test the switch. If you don\'t read the diagram right, this is the time you\'ll be glad you know where your breaker is located.
7. Put the wires in the switch box and then screw the switch to the box. (This is where the shorter of the screws go.)
8. Secure the the cords with the strain relief bar. Make sure that the flat part of the bar is down.
9. Screw the ground wires back to the plate and you\'re done.
Did you find this story helpful?
Thank you for voting!

Nothing. It was perfect

Franklin from St. George , Utah

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
121010214
Unscrewed two Phillip screws. Took the old off and put the new on. Then slid the bar back in. 10 minutes.
Did you find this story helpful?
Thank you for voting!

Bracket on extension broke on table saw

Bruce from Atlanta, Michigan

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
121010214
Just unscrewed they old ones and screwed on new brackets
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP18690529
Manufacturer Part Number: 121010214
Brand Model Number Description
Ryobi BTS16 Table Saw - 10" Table Saw
Ryobi BTS21 Table Saw - 10" Table Saw
Ryobi BTS211 Table Saw - 10" Table Saw
Ryobi RTS21 Table Saw - 10 in. Table Saw
Ryobi RTS21G Table Saw - 10-In. Table Saw