Part Location Diagram of 106-4410 Toro Lever-Traction
See part I-26 in the diagram
( Grid squares measure 1x1 inch )

Lever-Traction 106-4410

Manufactured by:
Toro
ERP Number:
ERP9256787
Part Number:
106-4410
Original Equipment Manufacturer ?
  Works with your model  38611!
$34.07
Special Order

Easy 

30 - 60 mins 

(1 rated repair) ?
  Works with your model   38611!

Troubleshooting

This part works with the following brands:
  • Toro
This part works with the following products:
  • Snow Blower
  • Chainsaw
Part# 106-4410 replaces these:
106-4410,

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

Be the first to ask our experts a question about this part!

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

30 - 60 mins 

(1 rated repair) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

I broke the traction lever and the throttle control know got brittle with age and broke

Jack from Lehighton, Pennsylvania

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Wrench set
Parts Used:
106-4410, 120-0132
1. Removed the 2 roll pins from the control ride near the right handle with a hammer and punch. Roll pins are not reusable so I re-installed cotter pins.
2. Removed the boot for the control rod tension spring and dog on the left side under the control panel.
3. Tapped the control rod through from left to right to clear for in stallation of the new traction lever.
4. Installed the new traction cable into the traction lever and dropped it in place.
5. Reinstalled the control rod tension spring dog and bolt. Be sure the dog is above the traction lever when installing.
6. Slid the control rod back through the left handle and traction control lever.
7 Aligned the roll pin holes with the right side handle and installed cotter pins. Cut them short for clearance.
8. Installed the traction control cable to the Lowe lever and adjusted out slack.
9 Installed the traction control lever tension spring to from the lever to the control panel ( black spring
10. Tested and adjusted with blower running.
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP9256787
Manufacturer Part Number: 106-4410
Brand Model Number Description
Toro 23740 Chainsaw - Walk-behind Rotary Broom, 2013
Toro 38595 Snow Blower - Toro Snowblower Model 38595 Parts
Toro 38597 Snow Blower - 38597, Power Max 826 O Snowthrower, 2013 (Sn 313000001-313999999)
Toro 38610 Snow Blower - Snowthrower
Toro 38611 Snow Blower - Snowthrower
Toro 38614 Snow Blower - 726 OE Power Max Snowblower
Toro 38620 Snow Blower - Snowthrower
Toro 38621 Snow Blower - Snowthrower
Toro 38622 Snow Blower - Snowthrower
Toro 38624 Snow Blower - Snowthrower
Toro 38624W Snow Blower - 38624w, Power Max 826 Oxe Snowthrower, 2012 (Sn 312000001-312008458)
Toro 38629 Snow Blower - Snowthrower
Toro 38629C Snow Blower - Snowthrower
Toro 38630 Snow Blower - Snowthrower
Toro 38631 Snow Blower - Snowthrower
Toro 38632 Snow Blower - Snowthrower
Toro 38633 Snow Blower - Toro Snowblower Model 38633 Parts
Toro 38634 Snow Blower - Snowthrower
Toro 38635 Snow Blower - Snowthrower
Toro 38637 Snow Blower - Snowthrower
Toro 38637C Snow Blower - Snowthrower
Toro 38639 Snow Blower - Snowthrower
Toro 38639C Snow Blower - Snowthrower
Toro 38640 Snow Blower - Snowthrower
Toro 38641 Snow Blower - Snowthrower
Toro 38642 Snow Blower - Snowthrower
Toro 38644 Snow Blower - Snowthrower
Toro 38645 Snow Blower - Snowthrower
Toro 38650 Snow Blower - Snowthrower
Toro 38651 Snow Blower - Snowthrower