This carburetor gasket is an authentic OEM sourced item that is specially designed to provide an air tight seal between the carburetor and the insulator plate. It is commonly utilized on small engines installed on lawn and garden equipment. Over time gaskets tend to get compressed and crack eventually requiring replacement. To replace this carburetor gasket you will need a set of screwdrivers.
Troubleshooting
This part works with the following brands:
MTD
Craftsman
Cub Cadet
Troy-Bilt
Yard Machines
Yard Man
Bolens
Husky
This part works with the following products:
Snow Blower
Engine
Tiller
Log Splitter
Chainsaw
Chipper Shredder
Part# 751P12005B replaces these:
751-11569
751-11569A
751-12005
751-12005A
751-12005B
751P12005A
951-11569
951-11569A
951-11569A-CM
951-12005
★
Customer Part Reviews
?
4.8
Average Rating (out of 5):
★★★★★
★★★★★
(5 Reviews)
Click to filter by ratings:
5 stars
4
4 stars
1
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Toro2410
Ordered carburetor rebuild parts for my Toro 2410 Snowblower. Parts were the exact same parts needed to rebuild the carburetor. Easy to rebuild with the parts ordered.
William - April 27, 2019
Verified Purchase
★★★★★
★★★★★
snowblower gasket
arrived fast, great fit
Guest - December 26, 2019
Verified Purchase
★★★★★
★★★★★
Easy repair
The only disappointing thing is the amount of time it takes to get your order delivered.
Guest - December 31, 2019
Verified Purchase
★★★★★
★★★★★
Start tiller but would not stay running.
I have a 2012 Super Bronco that I could start but would not stay running. Cleaned old carb several times, decided to replace with a new. Plus new spark plug. Still had the same issue. Finally found there was rust on the flywheel. Hubby fixed that and new pull rope. Now we’re running. Products I ordered did come quick and easy to find what I’m looking for. Thanks.
Laura - August 13, 2020
Verified Purchase
★★★★★
★★★★★
Easy ordering of parts,shipping was on time
You had eavery thing i needed,parts fit perfect put snowblower back together runs like new again.Thanks Tom
Guest - December 4, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
After taking the bowl off of the carberator it became clear that a new carberator was going to be needed. I just had to remove the fuel tank and control panel for access to the carberator. Swap in new carberator and reassemble. Set idle speed and my snowblower is good to go at a fraction of what a repair shop would have charged.
Did you find this story helpful?
Thank you for voting!
The ignition coilGÇÖs wire to the spark plug became so corroded at the spark plug it separated.
The ignition coil needed to be replaced. The following removal gave access to the coil for replacement.
1. Remove the top muffler cover, carburetor covering, and engine cover with engine rope starter which exposes the ignition coil.
Since the removal of the carburetor cover releases the pressure held onto the carburetor, thu
... Read mores possibly cause a carburetor gasket to leak I also slid the carburetor off and replaced the three gaskets in place between the engine head, carburetor, linkage bracket and air inlet. It is also required to remove the snow exit shoot to be able to access the two bolts that hold on the top engine cover.
2. Check gap of existing coil to flywheel magnet before detaching the coil. The coil detached with just one wire disconnected and two mounting bolts removed.
3. Cleaned the magnets on the flywheel.
4. Install the new coil and gapped it to approximately 20 thousands with a feeler gauge.
5. Install remaining removed items in reverse order. Test run.
The Yard Man never seemed to work quite right since the day I bought it but over the course of the winter it had gotten worse and after Googling, I figured it was a bad carb. I was right.
The hardest part was getting at it, but I found two good YouTube videos. One on taking the carb off (that took about two hours). And one o
... Read moren putting things back together.
1 Removed belt cover
2. Remove heat shield
3. Removed choke knob
4. Removed front cover housing plunger, key and choke control
5. Disconnected and plugged fuel supply line at carburetor bowl.
6 Removed fuel primer connection at carburetor
Found carburetor 370-SUA has the wrong type of choke conne
... Read morection, cobbled together by using choke base and rod from bad carb and mounting to brass base on new carb
Read less
Did you find this story helpful?
Thank you for voting!
Getting old ND needed some TLC
Steven from Brodhead, Wisconsin
1 personfound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
I cleaned the Engine, changed the Oil, replaced the Spark Plug replaced the coil assembly and replaced the Carb that was in bad shape. It went pretty smooth. You just have to lay out your parts and take your time.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_4.gif "Part Location Diagram of 751P12005B MTD Carburetor Gasket")
_WW_4.gif "Part Location Diagram of 751P12005B MTD Carburetor Gasket")
