This fuse is a high quality part sourced from the original manufacturer for DeWalt and Delta scroll saws. The fuse is a safety feature to prevent an electric surge from overloading the motor. Once the fuse is tripped it will burn itself out, and will need to be replaced. This part is sold individually, keep in mind the fuse cap is sold separately.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Great part
Fuse I needed for my $700 Delta scroll saw. Bought fuses locally they said would work.None did. Yours did. Thanks.
Guest - September 17, 2022
Verified Purchase
★★★★★
★★★★★
dewalt part
received on time and good condition, thanks
Guest - February 20, 2023
Verified Purchase
★★★★★
★★★★★
USPS
The USPS lost my order. Their tracking showed it was delivered but I never received it. I was able to find my old part. Not your fault!
Guest - July 1, 2023
Verified Purchase
★★★★★
★★★★★
Wrong Part
I ordered this fuse and a new fuse holder. The fuse holder was not a straight OEM replacement. The replacement fuse holder was configured differently than the OEM fuse holder which then required disassembly and modification of the scroll saw to accommodate the replacement fuse holder.
Guest - December 16, 2023
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
A Bit Difficult
1- 2 hours
(3 rated repairs)?
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
1. Remove old socket by pulling it out with pliers. Now realizing I need to get into saw.
2. Remove all screws from main housing and arm cover.
3. Remove saw table.
4. Open casing to reveal circuits.
5 Insert new socket housing from outside. Press on retaining ring from inside. Secure with hot
melt
... Read moreglue.
6 Reattach wires to socket.
7 Reassemble saw in reverse order as disassembly.
Removed stars removed from back cover.
Removed back brace for tilting fable.
Loosened star screws front of bottom cover.
Pulled back cover far enough to split apart.
Replace fuse holder from back to front.
Replace wires on to fuse holder.
Put back together in reverse order ensure wires are tucked
... Read more into cover where required.
Read less
Did you find this story helpful?
Thank you for voting!
Scroll saw hi speed was loud and choppy
lawrence from tabernacle, New Jersey
0 of 1 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Parts listed above were for a different issue (no power) ordered the parts listed above, and discovered a wire to the fuse assembly was off. Reset wire and saw ran, but very slow and and noisy if rheostat was turned up. I then ordered the PC board which arrived couple of days ago. Watched the video 2x and copied down the instructions to h
... Read moreave available in the shop. Disassembly was rather easy. Video stressed the different bolt lengths on parts of the assembly, so I tagged each bolt with a number and marked the housing holes with the bolt number to ensure correct placement..Got all the bolts out and removed the fore and aft housing pieces. At that point there\"s not much holding the rocker bar to everything else. this part was a little scary, fearful that a misplaced elbow would cause a disaster. So I recruited my wife to lend a hand and ensure it all stayed together ( and it did ). Removed the 3 screws holding the circuit board in place, and disconnected the 4 wires. Reassembled it with the new board. The next phase required 2 people to hold the pieces in place and align the bolt holes.all in all about a 2 hour process for me and the bride. Assembled the table to the saw and the saw to the stand...plugged it in and it was music to my ears... no chatter at high speeds just the nice sound of a new saw... Thanks to you guys at eReplacement parts. The video was extremely valuable as was the extra hands provided by my wife. I\"m happy again!
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10168837
Manufacturer Part Number: 286344-00
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of 286344-00 DeWALT Fuse,3a")
_WW_1.gif "Part Location Diagram of 286344-00 DeWALT Fuse,3a")
