Part Location Diagram of 651956-6 Makita Switch Tg72bd
See part 19 in the diagram
( Grid squares measure 1x1 inch )

Switch Tg72bd 651956-6

Manufactured by:
Makita
ERP Number:
ERP10153691
Part Number:
651956-6
Original Equipment Manufacturer ?
$38.97
In Stock
Delivers in 3-5 Business Days!

A Bit Difficult 

15 - 30 mins 

(3 rated repairs) ?

Does this part fit my model?

Need help finding your model number?

Product Description

?

This is a genuine manufacturer-sourced replacement component that is specially designed for use with Makita power tools. It is the part of the tool handling on/off operations, over time it may wear out and begin to fail eventually requiring a replacement. Keep in mind this high-quality plastic body switch is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this item.

Troubleshooting

This part works with the following brands:
  • Makita
This part works with the following products:
  • Saw
  • Circular Saw
  • Miter Saw

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

A Bit Difficult 

15 - 30 mins 

(3 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Switch and power supply circuit was bad,

Danny from austin, Texas

2 of 2 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
651956-6, 620125-0
With other work interruptions it took me longer to remove all of the screws holding the tool together than it took to replace the switch and power supply, put it all back together and another $200.00 tool was back in operation, about 15 minutes was all I needed.
Did you find this story helpful?
Thank you for voting!

Saw wouldnGÇÖt turn off or stop spinning unless battery was removed

Ted from Plantsville, Connecticut

1 person found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Parts Used:
651956-6
1-remove retention washer and nut from fence adjustment lever
2-Loosen screws to remove dust cover
3-loosen the 3 small flathead screws from existing switch one at a time, take note what wires go to what contact (or in my case I removed one at a time and attached to new switch before removing and attaching next wires from cont act until old switch was no longer connected and new switch was completely connected to wires)
4-put back together screws in dust cover until itGÇÖs very tight and sealed
5-replace but then retention washer on fence adjustment lever (be sure to check lever setting will work to tighten and loosen w/out coming down past the fence before Re-attaching retention washer)
6-enjoy Makita greatness
7-GET BACK TO WORK =ƒÿé

IT WAS A GREAT EXPERIENCE WITH EREPLACEMENT PARTS, I have no mechanical or electrical skills and repair only took 15 mins)
Did you find this story helpful?
Thank you for voting!

Trigger switch failure

Dean from Stratford, Iowa

0 of 1 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Parts Used:
CB441, 651956-6
Removed screws holding case together and removed snap ring and nut for depth adjuster. Pulled case apart , removed wires from switch and replaced. Uncrewed brush holders and replaced brushes.
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP10153691
Manufacturer Part Number: 651956-6
Brand Model Number Description
Makita 5026D Circular Saw - Cordless Circular Saw
Makita 5026DWB Circular Saw - Cordless Circular Saw
Makita 5036D Circular Saw - Cordless Circular Saw
Makita 5036DWB Circular Saw - Dustless Circular Saw
Makita 5046D Circular Saw - Cordless Circular Saw
Makita 5046DWB Circular Saw - Cordless Circular Saw
Makita 5620D Circular Saw - Cordless Circular Saw
Makita 5620DWA Saw - Saw
Makita 5621D Circular Saw - Cordless Circular Saw
Makita 5621DWA Saw - Saw
Makita 5630D Circular Saw - Cordless Circular Saw
Makita 5630DWD Saw - Saw
Makita BCS550 Circular Saw - 18V LXT Lithium-Ion Cordless 5-3/8" Metal Cutting Saw
Makita BCS550F Saw - Saw
Makita BCS550Z Nibbler & Shears - 18V LXT Lithium-Ion Cordless 5-3/8" Metal Cutting Saw
Makita BSS501 Circular Saw - 18V LXT Lithium-Ion Cordless 5-3/8" Circular Trim Saw
Makita BSS501F Saw - Saw
Makita BSS501Z Saw - Saw
Makita BSS610 Circular Saw - Circular Saw
Makita BSS610F Saw - Saw
Makita BSS610X2 Saw - Saw
Makita BSS610Z Circular Saw - 18V LXT Lithium-Ion Cordless 6-1/2&#34 Circular Saw
Makita LS711D Miter Saw - Cordless Miter Saw
Makita LS711DWB Saw - Saw
Makita LS711DWBEK Saw - Saw
Makita LS711DZ Saw - Saw
Makita LS800D Miter Saw - Cordless Compound Miter Saw
Makita LS800DWB Saw - Saw
Makita LSXL01Z Miter Saw - 18V LXT Lithium-Ion Cordless 7-1/2" Dual Slide Compound Miter Saw
Makita LXCU01Z Saw - Saw