This sander pad is a genuine Dewalt replacement part, not generic or aftermarket. It it a Foam Rubber type pad and is compatible with clamp-on style sandpaper. It is not compatible with hook-and loop sandpaper. This sander pad has a metal backing plate with a padded sanding surface attached. The pad is complete and ready to install. This sander pad will fit the Dewalt sanders listed in the 'Compatibility' section below. It is not guaranteed to fit any other power tool models.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
exactly what I needed!
Quick service! Computer skills of a kindergartener but procedure was easy and stressless. I'll stay with eReplacement for all my workshop and gardening/lawn equipment needs!
Anita - September 19, 2019
Verified Purchase
★★★★★
★★★★★
Exactly the part I needed.
Arrived in a very short amount of time and the quality is perfect. Very pleased with the part and the entire experience.
Guest - October 5, 2019
Verified Purchase
★★★★★
★★★★★
Easy repair
Swapped out pads and works like new. Got a second one for down the road.
Guest - November 20, 2019
Verified Purchase
★★★★★
★★★★★
replacement pad for Porter Cable sander
The pad fit perfectly on my old sander and it works good as new again!
Guest - March 5, 2020
Verified Purchase
★★★★★
★★★★★
Great Part
New part fitted great.
Guest - May 12, 2020
Verified Purchase
★★★★★
★★★★★
Good service
Fast service
Guest - July 2, 2020
Verified Purchase
★★★★★
★★★★★
Simple repair and great service.
Got a new switch, brushes, and sanding pad for a 20 year old Dewalt palm sander. All the parts fit perfectly and the sander performs just fine.
Guest - July 23, 2020
Verified Purchase
★★★★★
★★★★★
Fits perfectly!
Arrived in good condition and easily replace the damage part!
Guest - September 7, 2020
Verified Purchase
★★★★★
★★★★★
exact replacement. Quick fix.
exact replacement. no complaints
Guest - February 1, 2021
Verified Purchase
★★★★★
★★★★★
Parts world as described.
The ordering process was very easy and each part was described perfectly.
Guest - April 26, 2021
Verified Purchase
< Prev
1
2
3
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Replacing a worn pad on a palm sander is an easy task. First turn the sander upside down and locate the four screws that secure the pad to the plate. These may be torx bit screws so beware of that. Remove the 4 screws and remove the rubber sanding pad from the sander. Clean the plate of any residual saw dust and dirt. This can be accom
... Read moreplished by blowing with compressed air and/or a rag soaked in a little mineral spirits. Next, put the new pad in place aligning the holes and replace the 4 screws. Your pad sander is ready to go. I have 2 DeWalt 1/4 sheet pad sanders that I use very hard and these pads wear down over time. Suggestion, some sandpapers have an adhesive on the back that can stick to and sometimes tear the sander pad. I know this from personal experience. Spraying a little WD-40 on the pad prior to putting sandpaper on will help prevent any sticking of the sandpaper when it\'s time to change it out. Good luck.
Remove 4 screws that hold on the base plate... install new base plate and tighten screws using a star-bit driver. Be sure that the screws are secured tightly, as they will tend to loosen up during use of the sander.
Thanks for the parts and terrific service. I enjoy using e-replacement parts.
Removed the worn pad by removing four screws. Then you can pull the platen off the tool. Remove the paper clamps from the old platen and attach them to the new one. Now is a good time to clean the inside of the sander with compressed air. I then placed the new dust seal on the platen and pressed the platen back on. Make sure you line the
... Read moreplaten up with the feet the screws go into. Then I screwed the new pad to the platen.
Removed 4 screws from the sanding pad, then removed pad. Removed the broken platen from bearing. Took off the the paper clamps from the old platen and placed them on the new one. Installed new platen back on sander, then installed the new pad with the 4 screws.
Did you find this story helpful?
Thank you for voting!
My sander suddenly became hard to handle - like it had a mind of its own! I disassembled the bottom part of the sander and found out that the platen was damaged beyond repair.
There are 4 screws holding the platen and the backing plate. Begin by unscrewing the backing. There are two clamps mounted on the backing which can be reused if you are replacing your backing plate - save these for later installation. The platen comes off next. Be sure to clean all the debris or dust from the sander before installing you
... Read morer parts. Don\'t forget to order the circular seal. The installation was very easy and self explanatory once you see the inside.
1. Removed the worn down sanding pad and broken platen.
2. I noticed that one of the brass screw holes that I screw the platen to the sander base had become loose. This was the most time consuming part of my repair to fix (and probably would never happen to anyone else).
3. After reassembling most of the sander back together,
... Read more I added the dust seal to the platen, screwed the platen and the pad back to the sander.
4. Problem solved; it runs like a champ.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10166489
Manufacturer Part Number: 151284-00SV
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
