Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
My Rotozip tool went from dead to alive in five minutes.
My Totozip tool was totally not working. Rather than just throw it away I opened it up to see what was wrong. There are two small springs that keep the brushes in contact with the rotor. One of them had busted. I ordered a replacement part and installed it in less than five minutes. When I assembled the too it worked perfectly and it continues to do so. This was at about one fifth of the cost of a new Rotozip. Happy customer.
Guest - April 20, 2019
Verified Purchase
★★★★★
★★★★★
perfect match!!!
My rotozip is back up and running.
Guest - July 16, 2019
Verified Purchase
★★★★★
★★★★★
Perfect fit
Perfect fit, relatively easy replacement, Rotozip works like new again.
Mark - November 12, 2019
Verified Purchase
★★★★★
★★★★★
Replaced the brush holder assembly
At first I was skeptical, but I ordered the brush holder assembly anyway. To my surprise it fit perfectly and it was an easy repair. Now my Roto-Zip R20 works like new again.
Guest - March 11, 2020
Verified Purchase
★★★★★
★★★★★
it worked
Thanks for the part :) saved me some dough
Guest - April 14, 2020
Verified Purchase
★★★★★
★★★★★
Order cam in correctly
Part arrived in great condition
Guest - May 12, 2020
Verified Purchase
★★★★★
★★★★★
Perfect fit
Fast shipping, exactly what my rotozip needed.
Bradburd68 - May 8, 2020
Verified Purchase
★★★★★
★★★★★
Correct part
Quick ship, not difficult to replace; worked as expected.
Guest - November 17, 2020
Verified Purchase
★★★★★
★★★★★
My go to for parts
Part arrived very quickly, in safe packaging and was exactly what was needed. Great company couldn't be happier.
Richard - September 17, 2022
Verified Purchase
★★★★★
★★★★★
Brush set
Fastest shipping I ever received from ereplacement, thanks. Website and part all worked with excellence.
Guest - December 10, 2022
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Disassembled the tool and found a broken brush spring and worn brushes.
2. Tested the switch with an ohmmeter to ensure it was OK.
3. Ordered a replacement brush holder assembly, which includes new springs and brushes.
4. Cleaned all internal parts and the inside of the case. Used zero residue contact cleaner for the
... Read morecommutator (cleaning took the most time as the tool was very dirty inside from years of use).
5. Installed the new brush holder assembly. It plugs into the motor like a cartridge.
6. Reassembled the tool.
7. Tested the tool-- works great!
Read less
Did you find this story helpful?
Thank you for voting!
brush block housing assy cracked. v- speed wouldn\'t stay in any detent.
Remove housing screws, cut data decal,separate half\'s. don\'t loose spring for blade removal lock pin. pay close attention to wire positioning ( take photo ) remove armature, pry brush block assy away armature housing, dust and clean. unplug V-speed switch ( if changing ). Assembly is reverse. once the new brush block is in position and
... Read morearmature assy has been installed you must release the brush blocks so that they press against the rotor of the armature by positioning the small spring over the back side of the brush for each brush ( it loos like a small pin off to the side of the rear end of the brush holder) using a small blade screw driver pop it over to the center of the rear of the brush. Once you start to move it from its assembly position it will move on its own and automatically center. Assemble other half of housing and take care not to over tighten the screws, tighten them just beyond snug but don\'t torque them to much.
Read less
Did you find this story helpful?
Thank you for voting!
Broken brush tension spring was the culprit. Replaced the whole assembly anyways and saved the old brushes for backups, they were still in decent shape.
My Bosch Rotozip RZ20 stopped working one day, figured it was most likely the brushes.
Use a razor blad to cut the labels on the top and underside of the unit. Use the required bit in your screwdriver to remove all 6 screws and then separate the two parts of the main body. Replacing the brush assembly is easy and strait forward f
... Read morerom this part on.
My Rotozip worked flawlessly after the replacement.
1. Removed screws from housing.
2. Removed power wires from armature.
3. Removed alignment bushing from armature shaft.
4. Removed old Bush holder Bracket.
5. Installed new bracket.
6. Reassembled housing.
After a bit of troubleshooting, I discovered a broken motor brush spring was the reason my RotoZip tool stopped working. I ordered a brush assembly from eReplacement Parts and replaced the assembly for a whole lot less than the cost of a new RotoZip. The most time-consuming part of the repair was cleaning the commutator. I figured if I w
... Read moreas going to fix it I might as well do it right. Some YouTube videos helped. It sounds harder than it was and my RotoZip works great once again.
Replaced brush with holder. I did damage an electrical terminal end while trying to reassemble. You must pay close attention to the wire routing, not ANY extra space inside.
Original brushes were over worn. Spring no long kept them in contact with armature. Replaced brush assembly and was back in business. Great part. Fit perfectly.
Did you find this story helpful?
Thank you for voting!
Spring was broken on Brush holder assembly. Did not realize spring was broken until received the new part. The spring holds the carbon brush in place.
1) Removed 6 torx 20 screws.
2) Split housing cut labels along case joint.
3) Removed power connections to brush holder assembly( two white leads) needle nose.
4) Removed armature and brush assembly. (Cleaned housing and armature).
5) With flat screwdriver eased brush assembly off armature, holding brushes back in
... Read moreholder.
to ease over armature pivot wheel below brush assembly.
6) Eased brush assembly over pivot wheel while holding brush contacts in brush housings.
7) Pushed brush holder pins into armature, releasing brush contacts onto armature.
8) Connected power contacts back onto brush holder assembly.
9) Re-inserted armature assembly back into housing and replaced screws.
Tested operation good as new.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP19512889
Manufacturer Part Number: 2610920317
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
