This is a genuine Porter Cable replacement part, it is sold individually. This Brush Cap is used on the model numbers shown below. To remove this part ,simply use a flat head screw driver. Don't use top much pressure on it, they do have a tendency to break.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Easy repair and the video was a great help
Arrived quickly and fit perfectly
Guest - June 3, 2019
Verified Purchase
★★★★★
★★★★★
Very easy repair
The brush cap arrived in perfect condition, and the router is back running in like new condition.
Michael - July 12, 2019
Verified Purchase
★★★★★
★★★★★
A perfect fit
Just what I expected. Fits perfectly
Guest - September 4, 2019
Verified Purchase
★★★★★
★★★★★
Great Part with Fast Shipping.
The right part, with fast shipping. Thank You.
Guest - February 18, 2020
Verified Purchase
★★★★★
★★★★★
Parts for a Porta Cable Router rebuild.
It was a very good experience as always. Parts arrived on time, nothing was missing and the router runs like new again.
Dean - May 2, 2020
Verified Purchase
★★★★★
★★★★★
Easy repair
Less than a couple of minutes to replace. You just have to remember to push the brush in to where it catches on the motor in its slot before trying to screw the cap on.
Keith - December 29, 2020
Verified Purchase
★★★★★
★★★★★
Perfect part, Great price
Easy to order, arrived quickly, My Belt Sander is working great now.
Rick - February 27, 2023
Verified Purchase
★★★★★
★★★★★
Brush cap
Fast service. High quality. Never disappointed!
Gene - March 10, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
ereplacement parts has a perfect video giving exact instructions for dyi repair. Only special tools needed were an impact driver and 1-1/8 socket to remove the collet base from the armature shaft.
Just follow directions in their video and you will have no problem.
Removed the tabs with the tin snips, inserted the brushes, put brush cap on and tightened.
Original brush cap fell out and caused the circular saw not to have full power.
Remove the old brush caps with a screw driver, then remove the brushes. Install the new brushes in the brush holders Challenge getting the brush assembly to stay \" down\" or \"in\" until the new brush caps can get placed properly to engage threads. Persistence paid off.
Did you find this story helpful?
Thank you for voting!
Brushes wore out and shoe assembly was original equipment and needed replacing on a vintage Porter Cable, A-3, Take-About belt sander.
Removed the brush caps, slid in the new brushes and re-installed the brush caps.
Removed the three screws that held the shoe assembly, discarded the old shoe, placed the new shoe in position, re-installed the three screws.
Strapped on a new sanding belt, plugged it in, pulled the trigger switch, readjusted the belt and went to
... Read more sanding.
Saw a 690 Series Porter Cable router at an auction that wouldn\'t start. Noticed that it was missing carbon brushes and caps. Replaced them and boom, it started. Thus, was able to get a router, plunge router accessory, and another adjustable base for $80.00. Was able to use your site to identify the correct replacement parts, install them
... Read more and obtain an excellent tool for a boat load of savings.
I did not complete the repair/replacement because the brush caps sent didn\'t fit my porter cable router but I eventually found ones that did fit at a Dewalt/Black and Decker repair/parts store in California. Just a simple screw in cap screw to capture the brush spring end. I kept the ones sent because they were relatively inexpensive a
... Read morend not cost effective to send them back plus I have another tool that they will work on if need be.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP12494900
Manufacturer Part Number: 803483
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Cap or Lid","title":"Cap or Lid","url":"/parts/power-tool/router/caps-and-lids/"},{"position":2,"name":"803483","title":"803483","url":""}]
