Part Location Diagram of 682063 DeWALT CONNECTOR VS
See part 201 in the diagram
( Grid squares measure 1x1 inch )

CONNECTOR VS 682063

Manufactured by:
DeWALT
ERP Number:
ERP12464045
Part Number:
682063
Original Equipment Manufacturer ?
  Works with your model  314!
On Order

A Bit Difficult 

30 - 60 mins 

(3 rated repairs) ?
  Works with your model   314!

Product Description

?

It is a genuine item which is made for use with Porter Cable power tool. This part is supplied directly from the original equipment manufacturer. It is a special component which helps to connect two lead wires. The part is utilized to connect the on/off switch to the tool. It is a simple plastic item which is sold individually. Replacing it will only require a screwdriver, take apart the housing, remove the old part and secure the wires using the new connector.

Frequently Purchased Together

?

Troubleshooting

This part works with the following brands:
  • Porter Cable
  • DeWALT
  • DeVilbiss
  • Black and Decker
  • Delta
This part works with the following products:
  • Router
  • Sander Polisher
  • Reciprocating Saw
  • Laminate Trimmer
  • Sander Grinder
  • Jig Saw
  • Trimmer
  • Circular Saw
  • Planer Jointer
  • Belt or Drum Sander
  • Sander
  • Miscellaneous
Part# 682063 replaces these:
682063, P682063,

Customer Part Reviews

?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(1 Review)
Click to filter by ratings:
  • 5 stars
    1
  • 4 stars
    0
  • 3 stars
    0
  • 2 stars
    0
  • 1 star
    0
  • 1
Sort by:  
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

Be the first to ask our experts a question about this part!

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

A Bit Difficult 

30 - 60 mins 

(3 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Switch was bad,

Jonathan from Midway, Georgia

2 of 2 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Parts Used:
682063, 911373
1. Removed screw holding rear cover.
2. Removed cover.
3. Removed connector from black wire with needle nose pliers by opening crimp.
4. Disconnected wire from switch to spade using needle nose pliers.
5. Removed old switch.
6. Installed new switch in reverse order using crimping tool on new connector.
7. Plugged in to receptacle and tested switch.
Did you find this story helpful?
Thank you for voting!

The cord, sleeve and pad needed replacement.

ROBERT from MANHASSET, New York

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
802303, 879182, 682063, 895035, 838270
I removed the top half of the housing, replaced the cord and sleeve. Then removed the old pad and cleaned the surface. I put a small piece of very thin metal duct tape over the bearing hole. Then I sprayed a light coat of 3M high tack adhesive on the pad and reinstalled it....Job done!!
Did you find this story helpful?
Thank you for voting!

Power cord to switch on jig saw shot.

Gerald from Summerville, South Carolina

0 of 1 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
849314, 682063, 875863
Took the handle off, picture of internal electrical wire from pc, played New pc wires next to old ones, marked length of each color of wire(plus extra for placement in handle), the stripped each wire & paired each & applied each closed end connectors with crimmper. Stripped ground wire ,applied terminal connector & crimped it.
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP12464045
Manufacturer Part Number: 682063
Brand Model Number Description
Porter Cable 1001-T2 Router - Router
Porter Cable 1078 Sander Grinder - Porter Cable 1078 Parts
Porter Cable 167 Planer Jointer - Block Plane
Porter Cable 205 Sander Grinder - Porter Cable 205 Parts
Porter Cable 22-7301-56 Laminate Trimmer - 220v Laminate Trim
Porter Cable 22-7310-56 Trimmer - 220v Laminate Trim
Delta 23-9748-50SEV Reciprocating Saw - Pc 230v Tiger Saw
Porter Cable 259385 Sander Polisher - Drywall-Sander
Porter Cable 259485 Sander Polisher - 110V Drywall-Sander
Black and Decker 300713 Reciprocating Saw - Flex VA Tiger Saw
Porter Cable 304 Sander Polisher - 7&#34 Disc Sander
Porter Cable 305 Sander Polisher - Sander / Polisher
Porter Cable 309 Laminate Trimmer - Laminate Trimmer
Porter Cable 3092 Laminate Trimmer - Laminate Trimmer
Porter Cable 310 Laminate Trimmer - Laminate Trimmer
Porter Cable 3102 Laminate Trimmer - Laminate Trimmer Motor
Porter Cable 313 Laminate Trimmer - Porter Cable 313 Parts
Porter Cable 314 Circular Saw - Trim Saw
Porter Cable 314H Circular Saw - Trim Saw
Porter Cable 319 Laminate Trimmer - Tilt Base Trimmer
Porter Cable 3191 Laminate Trimmer - Tiltbase Laminate Trimmer
Porter Cable 320 Planer Jointer - Abrasive Planer
Porter Cable 330 Sander Polisher - Finishing Sander
Black and Decker 331678 Reciprocating Saw - Recon Flex Reciprocating Saw
Porter Cable 336 Sander Polisher - 3x21 Rockwell Belt Sander
Porter Cable 337 Sander Polisher - 3x21 Belt Sander
Delta 34-695 Table Saw - 10&#34 Table Saw
Porter Cable 348 Jig Saw - Bayonet Saw
Porter Cable 351 Sander Polisher - 3x21 Belt Sander
Porter Cable 352 Sander Polisher - 3x21 Belt Sander