Makita Saw Seals and Gaskets

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling - O-ring has ragged, tattered edges. These are commonly ...

It is a genuine replacement part that is supplied directly from the original equipment manufacturer for use with Makita reciprocating saws. This is the special component which is used to provide an air-tight seal for the gear housing assembly, over time the material tends to deteriorate and may crack eventually requiring replacement. It is a high-quality part which is made of durable rubber and it...

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling O-ring has ragged, tattered edges. These are commonly caused by p...

This is a genuine Makita replacement part that has been sourced from the original manufacturer to be used with angle grinders and die grinders. The o-ring is commonly used to seat and support the drive gear bearing assembly. This item is sold as an individual replacement part.

This is a genuine Makita replacement part for use in saws. The seal plate goes next to the plane bearing. A set of pliers and an allen wrench may be needed during the replacement of this part. It is made out of foam and will need to be replaced if it rips. This item is sold individually.

This is an authentic manufacturer-sourced component which is specially designed for Makita power cutters. The purpose of this gasket is to provide a tight seal for the cylinder, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Unfortunately, over time the material will wear out and it may begin to fail eventually requiring ...

This is an authentic Makita replacement part manufactured for use with cut-off saws. This gasket forms a seal between the carburetor and air connection sleeve. It is recommended to replace carburetor gaskets when servicing the carburetor or air cleaner to ensure a good seal when the parts are reassembled. This gasket is available as an individual replacement parts.

This is an original replacement part sourced directly from the manufacturer. The gasket is commonly found in Makita yard tools such as trimmers, edgers, blowers, and chain saws. This part is made of flexible plastic, and is used to seal the connection with the metering diaphragm. You will require a screwdriver when replacing this item. The gasket is sold as an individual replacement part. Inc...

This replacement o-ring is supplied directly from the original equipment manufacturer, it is specially designed for use with Makita power tools. It helps to provide an air-tight seal between connected pieces, please make sure to check appropriate diagrams of your model for the correct location and application of this hardware. It is made of high-quality rubber material and it is sold individually.

This is an authentic Makita replacement part manufactured for use with reciprocating saws. The seal helps guide the slider and prevent debris from entering the gear case. This seal is sold as an individual replacement part.

This is an original replacement part sourced directly from the manufacturer. The O-ring is commonly found in Makita rotary hammers, metal cutting saws, and circular saws. This part is made of flexible rubber, and is commonly used to seal the connection between components. It may be found in various locations in the machine, depending on model. Please be aware that there are different O-rings u...

This is a genuine Makita replacement part used in compatible saws. The gasket attaches to the bearing box. A screwdriver may be necessary during the installation of this part. It may become broken and will need to be replaced. This part is made of a thin material and is available individually.

This is an authentic Makita replacement part, sourced from the original manufacturer for use with power tools. The special oil seal is commonly used to seal the connection between a spindle or shaft and a gear case housing. This oil seal is available as an individual replacement part, please see model diagram for associative parts.

This is a genuine replacement part sourced directly from the manufacturer. The dust seal is commonly found in Makita power tools such as circular saws and planers. This part is made of metal and flexible rubber, and is used to prevent dust from clogging the armature or bearing and hindering their motion. You may require a screwdriver or wrench when replacing this item. The dust seal is sold as...