Husqvarna Pressure Washer Hoses and Tubes

An authentic OEM replacement fuel line that is specially produced for use with gas powered endings commonly installed on generators and other equipment. The fuel line is used to deliver the fuel from the tank into the carburetor. Over time lines may become brittle and may crack eventually requiring replacement. This item is made from durable rubber material and it is sold individually.

It is a high-quality item that is supplied by the original equipment for use with Briggs and Stratton, Troy-Bilt and Snapper pressure washers. The kit includes a fitting that allows a user to connect the hose that supplies the chemical cleaning solution. Unfortunately, over time components on your equipment may wear out or get damaged eventually requiring a replacement. Make sure to check the appr...

This is an authentic replacement part manufactured for use with pressure washers. The nozzle is used to provide an even spray when using soap or a chemical cleaner. This black soap nozzle is available as an individual replacement part, please see model diagram for nozzle kits for a specific model pressure washers.

This is a genuine OEM sourced replacement part that is intended to be used with pressure washers from Craftsman. The screen fits into the water inlet tube and is used to prevent debris from the hose from entering the pump assembly. This item is available as an individual replacement part.

This chemical injector kit is an OEM component direct from Briggs & Stratton. Made for use with the 020490-00 3,100 PSI Pressure Washer, includes parts designed to inject chemical solutions into the pressure washer water. An adjustable wrench is needed for the repair.

This is an original replacement part manufactured for use with pressure washers. This quick change nozzle delivers a 40-¦ angle spray for use with several pressure washing applications. The white quick change nozzle is sold as an individual replacement part.

This authentic manufacturer-supplied part is specially designed for use with Briggs and Stratton, Troy-Bilt and Snapper pressure washers. It is a special hardware that helps to secure components. This is an identical replacement for a missing or a damaged retainer clip that was installed on a new unit. Note, it is made of durable plastic and is sold in a pack of four. Make sure to refer to the own...

This is a genuine part that is used to replace the original hose that is used with pressure washers from Briggs & Stratton and Snapper. The clear plastic hose is used to relay liquid soap from the detergent reservoir and the pump assembly. This item is available as an individual replacement part.

This is an authentic OEM replacement nozzle made to fit the pressure washers listed below. This is a standard sized quick connect nozzle with a forty (40) degree spray pattern. This nozzle can be used on any surface, and is recommended for materials that are prone to scratches or paint loss such as stucco or car exteriors. Sold individually.

It is an OEM supplied Ez Start kit which is designed for Troy-Bilt and Briggs and Stratton pressure washers. This is a special mechanism which makes starting the engine easier by relieving pressure within the pump head. Unfortunately, over time components may wear out and begin to fail eventually requiring replacement to ensure your equipment runs properly. Note, this high-quality kit includes mul...

This is an authentic OEM sourced replacement part that is intended to be used with pressure washers from Troy-Bilt and Briggs & Stratton. The red nozzle is 0-¦ and attaches to the end of the spray wand. This nozzle emits a small concentrated stream of water. The red nozzle is used to remove tough stains in concrete and metal. It is advised to not use this nozzle on wood or siding because this nozz...

This is an authentic OEM part for use with Briggs and Stratton Pressure Washers. The chemical injection connector connects the chemical injector to the pump. This part is sold individually. The most common reasons for replacing the injector kit are when water is getting into the soap dispenser, the chemical injector nozzle is leaking, or the pressure washer soap injector is not working at all. The...

This is an authentic OEM part designed to fit the pressure washers listed below. This is a yellow chiseling style tip, with a standard fifteen (15) degree spray width. This nozzle is recommended for water only. It is ideal for heavy duty pressure washing of harder surfaces and stubborn stains/grime. This is a very commonly used nozzle so a backup could be handy. Sold individually.