Porter Cable Nailer Springs and Shock Absorbers

Genuine OEM replacement part, this item is sold individually. This spring is mounted to the pawl. After a nail has been fired it will close the pawl so that the next nail may be fired. This part is used by the roofing nailers listed below.

This is a genuine OEM sourced part that is intended to be used with pneumatic nailers and staplers from Bostitch, Porter Cable, and DeWalt. The metal spring is used to provide compression between the piston head valve and the end cap assembly. This item is sold as an individual replacement part.

It is an authentic OEM component which is made for Porter Cable nailers. This spring applies tension on the trigger allowing it to retract. If the spring is stretched, damaged or lost, this part will provide an identical replacement for the original hardware that was installed on a new unit. One durable metal spring is included. Replacing it is a simple task that should not require any special too...

This is an authentic OEM component from Bostitch. The depth adjust cam spring is compatible with several pneumatic nailer devices. Fitted between the trip assembly and the lower contact arm, providing the necessary resistance. This component is sold individually. A screwdriver and a pair of pliers are often helpful with the repair.

This is an authentic OEM replacement part manufactured for use with pneumatic staplers and brad nailers. The metal spring is used to provide compression for the click lever on the magazine. This spring is sold as an individual replacement part, please see model diagram for associative parts.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with pneumatic fasteners from Bostitch, Porter Cable, and DeWalt. The metal spring is part of the magazine assembly and is used to provide tension on the pusher that moves nails or staples toward the nose of the fastener. This spring is available as an individual replacement part.

This Torsion type spring is an authentic Porter Cable replacement part. It is sold individually.

This item has been sourced from the original manufacturer and is intended to be used with finishing staplers from Bostitch and Porter Cable. The metal spring is part of the safety contact trip. The spring is used to provide compression when the safety is pressed against the material being fastened. The spring is sold as an individual replacement part.

This authentic manufacturer-supplied component is made for Porter Cable staplers. The spring applies tension on the connected pusher inside the magazine. Over time it will wear out and it may begin to stretch eventually requiring a replacement. This high-quality spring is made of durable metal and is sold as an individual item. Check the diagrams for your model to ensure the proper repair procedure.

This is a genuine manufacturer-sourced part is specially designed for use with Porter Cable staplers. It provides an identical replacement for a missing or a faulty spring that was installed on a new unit. The part is utilized to apply tension in the magazine, please check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quali...

This is an authentic replacement part manufactured for use with Porter Cable pneumatic framing nailers. The spring is commonly used to provide tension against the pusher on the cover assembly. This spring is sold as an individual replacement part, please see model diagram for associative parts.

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Porter Cable nailers and staplers. The spring is generally utilized to apply tension to the trigger valve assembly, unfortunately, over time it will wear out, stretch or it may get lost eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your model for the...

This is an authentic Porter Cable replacement part manufactured for use with finishing nailers. The rubber pad is commonly used to provide spacing and cushioning between the end cap and the exhaust deflector. This rubber pad is sold as an individual replacement part.

This genuine item is supplied directly from the original equipment manufacturer for use with Porter Cable nailers and staplers. It is an identical replacement for a missing or a faulty spring that was installed on a new unit. The purpose of this spring is to apply tension on the plunger, please make sure to refer to the appropriate diagrams of your model for the correct location and application of...

The spring fits between the seal and the o-ring. This authentic item is supplied directly from the original equipment manufacturer for use with nailers and staplers made by Porter Cable. This part is sold individually and is made of metal. A wrench and a set of pliers might be helpful during the installation of this part. It will need to be replaced if it breaks or bends.

This is an authentic manufacturer-sourced part that is specially designed for use with DeWALT and Porter Cable power tools. It is an identical replacement for a faulty or a missing torsion spring that provides tension for the magazine that holds the nails. Please make sure to refer to the diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quali...

The spring fits between the driver guide and the latch. This is a genuine Porter Cable replacement part for use in nailers and staplers. It is made out of metal and is available individually. If this part becomes bent or broken it will need to be replaced and may require an allen wrench and a set of pliers during the installation.

This part is an OEM from Porter Cable. The metal spring is made for use with many nailers and staplers. This item is often secured between the piston stop and the valve piston head, providing the needed tension. The spring is sold individually. A hex key and pliers are helpful for the replacement process.