Porter Cable Nailer Seals and Gaskets

This is an authentic Bostitch replacement part used on specific Nailers. This is a Rubber Ring and it is sold individually. O-rings are designed to withstand thousands of pounds of pressure by creating a seal between two or more parts.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling • O-ring has ragged, tattered edges. These are commonly cau...

Genuine Porter Cable replacement part, this item is sold individually. The Head Valve Seal is in stalled on top of the 904695 Cylinder. It provide a seal for the Head valve. If you air leaks in your nail gun you may consider the part number 904949 Overhaul Kit. It includes the Head Valve Seal and other internal parts to stop air leaks

This is a Genuine Manufacturer Sourced replacement part designed for Nailers/Staplers. This O-Ring provides an Air-Tight Seal for the Valve Piston. Over time this O-Ring will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of Rubber and it is Sold Individually. Replacing this item you would need Hex Key/Allen Wrench and Pliers to replace this item.

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with pneumatic nailers and staplers. The seal is used to prevent leaks between the head valve and the end cap spacer. This item is available as an individual replacement part.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling • O-ring has ragged, tattered edges. These are commonly cau...

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common are: • Extrusion and Nibbling - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" f...

This is a Genuine Manufacturer Sourced replacement part designed for Nailers/Staplers. This O-Ring provides an Air-Tight Seal for the Driver Unit. Over time this O-Ring will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of Rubber and it is Sold Individually. Replacing this item you would need Hex Key/Allen Wrench and Pliers to replace this item.

Genuine Bostitch replacement part, this item is sold individually. The 850607 is used in the Bostitch pneumatic tools shown below. It is used in different areas of some of these tools.. The most popular is being installed on the piston of most of the nail guns shown to help create a seal. On the Staplers it is installed on the cylinder, also to create a seal. Over time seals will wear and crack an...

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling - O-ring has ragged, tattered edges. These are commonly...

Genuine Bostitch replacement part, this part is sold individually. The purpose of this O-Ring is to create a seal around the Piston Stem of the Bostitch Floor Nail Guns shown below. Over time O-Rings can wear and become brittle or stretched. When your Nail Gun becomes sluggish or the Driver won't retract, it may be time to tear the Gun down and inspect all of the O-Rings and Seals.

This is a manufacturer sourced replacement part. This seal is used on Porter Cable nailers/staplers. This seal plays an important role because it helps to provide and air tight seal for the piston. Over time it will shrink, become brittle and crack allowing for air leaks. Replacing it should resolve the issue. It is a good idea to check other seals and gaskets in a tool when replacing one seal. It...

It is a genuine item that is supplied by the original equipment manufacturer for use Porter Cable nailers. This is an identical replacement for a missing or a worn o-ring was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. The part helps to provide a tight seal between connected components. Keep...

This part is an authentic replacement part used in various Bostitch and Porter Cable power tools. An o-ring is a gasket used to create a strong seal between solid pieces. It is a simple yet essential part of a tool. Please note that the proper size o-ring is necessary for proper sealing, and there are often more than one size used per tool. This piece is sold individually.

This genuine OEM part is found in various models of staplers/nailers manufactured by Bostitch, Porter Cable, and DeWALT. An O-ring is a bendable part used between solid pieces, creating a seal which can maintain and withstand high pressure. One machine may use multiple styles of O-ring and care is needed to ensure that the correct one is used in the correct place. Sold individually.

This piston O-ring creates a tight seal between the piston and cylinder, allowing proper air pressure to build for strong and consistent fastening performance. Made from durable rubber, it is designed to withstand repeated use while maintaining reliability. Replacing a worn or damaged O-ring can restore driving power and help prevent air leaks, ensuring your tool operates effectively.

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Porter Cable nailers and staplers. It helps to provide an air-tight seal between connected components, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber and is sold individually.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling • O-ring has ragged, tattered edges. These are commonly cau...

This is a genuine item that is supplied by the original equipment manufacturer for use with Porter Cable nailers. It provides a high-quality replacement for a worn or a missing seal that was installed on a new unit. To ensure the exact location and the correct installation, refer to the diagrams of your model. Keep in mind, this part is made of durable rubber material and is sold as an individual ...

This is a genuine manufacturer approved replacement o-ring used on Porter Cable nailers/staplers. O-rings are designed to withstand high pressure by creating a seal between two connected parts. Over time o-rings will damage and should be inspected periodically. If parts are showing signs of wear they should be replaced. This is a rubber o-ring and it is sold individually.