OEM Makita Demolition Hammer Parts & Accessories

$32.81

Manufacturer Part Number:: CB204

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New br...

Carbon Brush Set

★★★★★

(2)

$12.30

Manufacturer Part Number:: CB175

Genuine Manufacturer Sourced replacement part. This item is made out of Carbon with a Lead Wire attached. This item includes Two (2) Carbon Brushes per order. Please note Brush Holder and Spring are Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear...

Carbon Brush Set

★★★★★

(6)

$10.81

Manufacturer Part Number:: CB351

This is a Genuine Manufacturer Sourced replacement part used on Makita Rotary Hammers. Includes Two (2) Carbon Brushes with Lead Wires attached. Please note Brush Holders and Springs are Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they ...

Ball Bearing

★★★★★

(10)

$14.50

Manufacturer Part Number:: 211066-7

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. rnrn • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the balls reduce friction. This reduces wea...

O Ring 28

★★★★★

(1)

$5.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 213415-4

This is a genuine replacement part designed for use with Makita power tools. This o-ring provides an air-tight seal for the connected parts. Please make sure to check appropriate diagrams for location and use of this item. Over time o-rings will shrink, become brittle and crack allowing for air leaks. At that time they should be replaced. It is made out of rubber and it is sold individually.

Brush Holder Unit

$14.40

Manufacturer Part Number:: 632D00-2

This replacement brush holder unit is a high quality item that is supplied by original equipment manufacturer for use with Makita demolition hammers. Its purpose is to secure carbon brushes around the armature to maintain stable contact. This item is a complete assembly which includes the plastic ring, two metal brush holder with attached lead wires, please note the carbon brushes themselves are s...

Brush Holder Cap

$6.15

Manufacturer Part Number:: 643700-5

This is a manufacturer sourced replacement part designed for use with Makita power tools. It helps to secure the brush in the housing. This screw-in cap is made of hard plastic and it is sold individually and measures 7-18 HM 1500. To replace it you would need a flat-head screwdriver.

Switch

★★★★★

(5)

$33.27

Manufacturer Part Number:: 651922-3

This replacement switch is specially made for use on Makita power tools. Switches are a commonly replaced item in power tools. They play a key role by controlling on/off function of a tool. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. To replace this switch you would need a screwdriver. • First make sure the tools is not...

Carbon Brush Set, 197128-4

$10.78

Manufacturer Part Number:: CB218

Cord (2x18x16 Sj), Hm0810b

$41.06

Manufacturer Part Number:: 660254-7

Hammer Grease

$8.84

Manufacturer Part Number:: A-90582

This genuine manufacturer approved hammer grease is sold individually. This petroleum based grease is designed for use with Makita hammers. It helps to lubricate the system allowing for easy movement and protecting parts from usual wear.

Handle

★★★★★

(1)

$24.98

Manufacturer Part Number:: 418333-3

This genuine Makita replacement part is designed for use with breaker hammers. It is supplied directly from original equipment manufacturer. Its purpose is to provide user with a stable grip for a stable control of a tool. It also houses the switch. This handle is made out of black plastic and it is sold individually. Replacing this handle is a very simple and quick task. It should only require ...

Makita Demolition Hammer Parts

Top Makita Demolition Hammer Models

Popular Makita Demolition Hammer Parts

Makita Demolition Hammer Models

Shop by Popular Makita Demolition Hammer Part Types

Makita Demolition Hammer Parts

Search By Model or Part Number

Top Makita Demolition Hammer Models

Popular Makita Demolition Hammer Parts

Makita Demolition Hammer Models

Shop by Popular Makita Demolition Hammer Part Types