OEM Craftsman Impact Driver Parts & Accessories

RETAINING RING

$6.16

Manufacturer Part Number:: N421245

BRUSH ASSEMBLY

★★★★★

(2)

$6.16

Manufacturer Part Number:: 290255001

This replacement carbon brush is a genuine OEM sourced replacement part designed for use with a variety of power tools. This assembly includes one (1) carbon brush with a lead wire and a spring attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at ...

Compression Spring

★★★★★

(7)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: N019351

This is an OEM authorized part. It is sold individually. This spring maintains pressure on the N078437 Sleeve, and the rest of the bit holder assembly, to keep the bit in the holder. If this part fails the bit cannot be held in the bit holder. It is commonly used in impact drivers, and is compatible with the impact drivers listed below.

Steel Ball

★★★★★

(18)

$6.16

Manufacturer Part Number:: N089668

Genuine Dewalt replacement part, this item is sold individually. The N089668 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly.

Detent Pin

★★★★★

(3)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: N020802

This is a genuine Dewalt replacement part, it is sold individually. The purpose of the Detent Pin is to secure sockets to the anvil on the Impact Wrench model numbers shown below. It is held in the anvil by use of a spring and pin.

Washer - Urethane

★★★★★

(2)

$6.55

Minimum Quantity of 2 required

Manufacturer Part Number:: 642883-00

This is an authentic OEM part used in DeWALT and Porter Cable impact drivers. It fits between the anvil assembly and the sleeve. If it becomes lost or broken it will need replacing and a screwdriver may be needed during the installation. This part is made of urethane, a hard plastic, and is available individually.

Spring

★★★★★

(5)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: N437890

This is a spring designed to fit within the bit holder assembly of an impact driver, also known as an impact wrench. Positioned between the anvil and ring gear, this spring is accompanied by a washer and hog ring on each side to provide tension and maintain consistent pressure on the inserted bit within the holder. As a high-wear component, this spring will eventually wear out, resulting in a less...

Carbon Brush With Spring

★★★★★

(10)

$11.84

Manufacturer Part Number:: 450374-12

Genuine OEM replacement This brush is sold individually, 2 are needed for most every electric power tool It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the...

Hog Ring

★★★★★

(1)

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: N424032

This genuine OEM hog ring is used in impact drivers. It is a thick, circular wire with a diameter of 0.5 inches. It is positioned around the output shaft where it grips and secures the socket or adapter. Over time, the hog ring may corrode, break, or lose tension leading to socket instability. To remove a faulty hog ring, use needle-nose pliers or a small flat-head screwdriver to carefully pry it ...

Power Cord (8-foot)

★★★★★

(2)

$32.54

Manufacturer Part Number:: 330077-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 8 Feet Long

Carbon Brush With Lead

★★★★★

(5)

$9.98

Manufacturer Part Number:: 655213-02

Genuine DeWalt replacement part rnIncludes 1 Carbon Brush with wire lead in rubber sheath attached.rn • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear it...

Anvil Assy.

★★★★★

(2)

$23.21

Manufacturer Part Number:: N439275

Craftsman Impact Driver Parts

Top Craftsman Impact Driver Models

Popular Craftsman Impact Driver Parts

Craftsman Impact Driver Models

Craftsman Impact Driver Parts

Search By Model or Part Number

Top Craftsman Impact Driver Models

Popular Craftsman Impact Driver Parts

Craftsman Impact Driver Models