Craftsman Compressor Hardware

Genuine OEM replacement part, this item is sold individually. This part is used in various places in the compressors listed below. By its part name, it is used to clamp hoses onto certain parts on the compressors.

Genuine OEM replacement part designed for a variety of Air Compressors. This part is made out of Metal and it is Sold Individually. It does include sleeve. This item allows to connect two like-diameter fasteners or tubes.

This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individually. Purchasing spare screws is also encouraged, as they ca...

This is a genuine Craftsman part for use with Craftsman Air Compressors. The compression ring creates an airtight seal between the cylinder and piston and helps facilitate heat transfer between the piston and cylinder wall. The compression ring on a piston head is a wear and tear item. It is, often, a cause of an air compressor failing to produce air. This part is sold individually. Unplug the air...

Genuine OEM replacement parts kit. This Gasket Kit is used to prevent air leaks in the compressors listed below. Over time the gaskets will become compressed or cracked and you will hear an air leak coming from the compressor. They will need to be replaced. This would be a good time to inspect all the other wear parts of the compressor.

Genuine OEM replacement part, this item is sold individually. A Pressure Switch controls the the compressor tank pressure. It will turn the compressor on when the tank pressure falls below the preset cut in point. It will also turn the compressor off at the preset cut point. This Pressure Switch is used on all of the compressor models shown below. One hose clamp included.

This is an OEM replacement part designed to fit Air Compressors. This nut is for the tube as it enters the head. It is made out of Metal and it is Sold Individually. To replace this item you would need a Wrench.

This screw is an authentic OEM replacement part sourced directly from the manufacturer. It is compatible with various models of electric compressors supplied by brands such as DeWALT, Black and Decker, and Bostitch. This screw should be replaced if it is lost or worn. It is made of metal and sold individually.

This is a genuine OEM sourced replacement part designed for use with air compressors. It is used to secure the crankcase cover to the unit. This part is made out of metal and it is sold individually. Requires a wrench to tighten/loosen this screw.

This is an authentic OEM sourced replacement component which is specially made for use with air compressors. It is a standard hardware which has multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this item. Keep in mind this high-quality bolt is made of durable metal and is sold individually.

This replacement screw is a genuine OEM sourced hardware that is designed for use with air compressors. It is generally used to secure the shroud, please make sure to check appropriate diagrams for correct application of this screw. One durable torx screw is included per order.

This is an authentic OEM sourced part that is intended to be used with air compressors from Porter Cable, DeWalt, DeVilbiss, and Black & Decker. The isolators connect to the bottom of the frame of the feet of the tank and are used to support the compressor. These items also absorb vibration between the ground and the tank. The isolators are sold in a kit of three and the hardware is included.

This replacement screw is a genuine OEM sourced item commonly utilized on air compressors and pressure washers. It is a standard hardware which has multiple applications depending on the unit. Please make sure to check diagrams of your model for the correct location and used of this screw. This part is made from durable metal and it is sold individually. You will need a wrench to install or remove this hardware.

It is an OEM component which is designed for use with air compressors. This special nut sleeve assembly secures the pressure relief tube to the pressure switch. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. One durable metal nut sleeve assembly is included. A wrench will be needed to perform this repair. Check the appropriate diagrams for yo...

It is a genuine item that is supplied by the original manufacturer for use with Ridgid self-opening die heads. This is a special pin that is utilized to secure the lock screw. Over time it may wear out or get damaged eventually requiring a replacement to ensure the correct repair procedure. Keep in mind this high-quality pin is made of durable metal and is sold as an individual item. Pliers might ...

This is a genuine replacement part sourced from the original manufacturer for use with generators and air compressors. The hex head screw is used with several different types of equipment and the application of the screw can vary based on the model of the machine. This screw is available as an individual replacement part.