OEM Dynabrade Grinder Parts & Accessories

Felt Silencer

$6.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 01486

This felt silencer is an OEM part direct from Dynabrade. Compatible with a variety of power tools, this component is fitted onto the shaft, between the locking ring and bearing. You may require a screwdriver or Allen wrench when replacing this part. The felt silencer is sold individually.

Spring

$6.55

Minimum Quantity of 2 required

Manufacturer Part Number:: 01468

This an authentic Dynabrade replacement part used in buffers and sanders. The spring is used to absorb shock from the valve when tool is in use. It goes between the air control ring and the tip valve. A wrench may be needed to properly install this part. This item is available as an individual replacement part.

Seal

★★★★★

(1)

$10.02

Manufacturer Part Number:: 01464

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench...

Bearing

$31.86

Manufacturer Part Number:: 02649

This authentic replacement part is designed for use with Dynabrade power tools. Ball bearings are used to reduce friction between rotating parts. It is one of the bearings for the rotor. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Over time bearings may begin to wear out compromising tools functionality and eventua...

Tip Valve

$18.00

Manufacturer Part Number:: 01472

This is a genuine OEM part. The Dynabrade tip valve is manufactured for use with orbital sanders, finishers and grinders. This metal and plastic valve often sits in the air inlet bushing, and is supported by a spring. The valve is sold individually, please see specific manual for additional repair information. A pair of pliers, wrench and a screwdriver may be necessary for installation.

Bearing

$32.56

Manufacturer Part Number:: 01007

This is an original part assembled by the original manufacturer. It is compatible with various Dynabrade handheld power tools, such as grinders and finishers. Ball bearings are used to buffer between moving parts. They also serve to keep parts correctly positioned while assuring steady directional movement. Ball bearings need frequent replacement because of this high-wear role. This steel part is sold individually.

Tip Valve

$19.63

Manufacturer Part Number:: 58365

This is a genuine Dynabrade replacement part manufactured for use with orbital sanders, and grinders. This special valve sits in the air inlet bushing, and is supported by a spring. The valve is sold individually, please see model diagram for additional parts that are available separately.

Throttle Lever Assy., Safety L

$67.56

Manufacturer Part Number:: 01950

This part has been OEM sourced and is intended to be used with buffers, sanders, right angle reciprocating filers, and die grinders from Dynabrade. The metal lever assembly includes the safety lock and attaches to the body of the tool. This item is used to actuate the valve stem to allow compressed air into the tool to drive the rotor. The throttle lever assembly is sold as an individual replacement part.

Silencer

$8.25

Minimum Quantity of 2 required

Manufacturer Part Number:: 01580

Blades/rotor (4 Pack)

$48.75

Manufacturer Part Number:: 01011

These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check the condition of the blades and replace them if they are vi...

Carbon Brush Set

$70.85

Manufacturer Part Number:: 40750

It is an authentic manufacturer-sourced replacement set which is specially designed for use with Dynabrade power tools. The brushes play the key role by conducting electric current while maintaining physical contact with an armature. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. When replacing carbon brushes, be sure to also inspe...

Blades

★★★★★

(2)

$46.88

Manufacturer Part Number:: 01480

These authentic OEM sourced replacement rotor blades are commonly used on Dynabrade sanders and grinders. They are attached to the rotor inside the tool pushing the air. This set includes (4) compound material blades per order. Replacing these blades you will need a set of wrenches and pliers.

Dynabrade Grinder Parts

Top Dynabrade Grinder Models

Popular Dynabrade Grinder Parts

Dynabrade Grinder Models

Shop by Popular Dynabrade Grinder Part Types

Dynabrade Grinder Parts

Search By Model or Part Number

Top Dynabrade Grinder Models

Popular Dynabrade Grinder Parts

Dynabrade Grinder Models

Shop by Popular Dynabrade Grinder Part Types