This OEM socket-outer is specifically designed for use with Echo handheld pruners. It connects to the drive shaft, enabling rotation of the trimmer head. Made from durable plastic, this high-quality component is sold individually and should be replaced if it becomes worn, cracked, or damaged over time. The inner socket is sold separately. Replacing the socket-outer is a straightforward process that typically requires only a screwdriver and a wrench to disassemble and reassemble the main pipe housing the drive shaft. For proper installation and application, refer to your model’s owner’s manual and diagrams.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Part was just as ordered
This was a OEM part and was delivered in a A timely matter just like all products ordered from site. Will definitely use them many more times in the future. Thankyou.
Marty M - April 23, 2019
Verified Purchase
★★★★★
★★★★★
Echo pole pruner part
My parts came super fast and fit my pole saw perfectly. No complaints!
Joseph - November 16, 2019
Verified Purchase
★★★★★
★★★★★
Echo pole saw
Got my polesaw fixed nice and easy fix
Guest - March 1, 2023
Verified Purchase
★★★★★
★★★★★
Status quo = meh
The part arrived in an average amount of time at best. It's just a standard part and nothing spectacular so I'm not sure why eReplacement parts hawked me for some special review. Ok, so they had the part.......great, wonderful, woo hoo.
Guest - October 28, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Took head off pole saw by removing the four screws that holds the head to the pole. Once they were removed pulled the head off and removed the damaged part and replaced with new part. Works great.
1. Remove cutter head by loosening two Allen head screws and set screw.
2. Loosen clamp assembly holding orange lower tube and upper black extention. Loosen set screw and remember direction which is down.
3. Pull black extention out of orange tune.
4. Inner shaft was bent along with outer upper tube. So, both had to be r
... Read moreeplaced.
5. Clean lower shaft that is exposed and reapply lithium grease.
6. Slide new inner drive shaft over lower drive shaft and leave about 12 inches exposed.
7. Slide new black extention tube into orange tube making sure hole on tube near cutter end is facing downward as this is
where the set screw reattaches with about 12 inches left out.. Place clamp that holds orange and black tube onto bottom of black tube where cutter head attaches and slide up to orange tube. This clamp must pass over the first stop rivet at the bottom. Use a screw driver to lightly pry apart clamp and gently push over this rivet. Push up clamp until it attaches to the orange pole. This clamp does not slide over the rivet closest to the bearing end already inserted. That rivet is the stop for when using extention and prevents from sliding extention out completely when extending. Slide over one rivet only. Tighten clamp at this time and make sure the extention works properly. Attach upper extention and drive to cutter head and tighten clamp.
8. Repair is complete. A very good video is on YouTube that explains what I just described.
9. I had some confusion on replacing the inner and outer sprockets. Just place some lithium grease in upper spline and slide in inner sproket followed by outer sproket. Did not make sense why the sprockets were just not one piece but no one could explain at Echo why.
Good luck and worked out on first try for me. I would recommend checking the chain sproket and buy a couple to save on shipping later as you will certainly need one replaced at some point.
Also make sure to order the parts for the correct series which is located on the saw. Mine started with 042 which is what was needed because Echo has three models of the PPT-266
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_2.gif "Part Location Diagram of C509000100 Echo Outer Socket")
_WW_2.gif "Part Location Diagram of C509000100 Echo Outer Socket")
