This is a genuine replacement part sourced from the original manufacturer for use with edgers, sanders, and miter saws. The special ball bearing is commonly used to reduce friction between a rotating shaft and fixed part assembly. This ball bearing is available as an individual replacement please see model diagram for associative parts.
Troubleshooting
This part works with the following brands:
Ridgid
Ryobi
Southland
Powermate
Airstream
Craftsman
Homelite
This part works with the following products:
Planer Jointer
Edger
Miter Saw
Part# 089210136012 replaces these:
079027013007
080038001475
678719001
820722-5
825541
971803001
A50062030045
C2600024BB
★
Customer Part Reviews
?
4.5
Average Rating (out of 5):
★★★★★
★★★★★
(2 Reviews)
Click to filter by ratings:
5 stars
1
4 stars
1
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Exact Part number installed & working
Shipping cost was more than the part thought it was rather exaorbant just short of ten dollars for a three dollar bearing.
Guest - February 5, 2020
Verified Purchase
★★★★★
★★★★★
Roller bearing
Perfect, easy to replace. The right stuff.
Francisco - July 29, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
The opening for the non-driven end of the planer shaft is too small for my smallest gear puller to fit through the bearing mount opening to pull the fused inner race of the failed bearing. The slot in the frame for the planner shaft for original factory installation was too small for the shaft to be removed with a fused inner race stuck o
... Read moren the shaft.
I opened up the slot for the original shaft installation slightly top and bottom to allow the race to slide through the opening so the fused Inner race could be removed with a small Dremel bit. Once the inner race was removed. I cleaned all of the associated parts and mounts and reassembled the shaft with the new bearings and chains.
Read less
Did you find this story helpful?
Thank you for voting!
Bought a used ridgid jointer and replaced the worn out parts
1. Removed the fence with the slide all together by loosening two rear allen bolts ( careful it is very heavy so if you can get another person to help you remove it)
2. Remove the guard cutter.
3. Remove the pulley guard cover.
4. Remove the belt.
5. Lower both infeed and outfeed table.
6. Loosen both hex
... Read morescrews that hold the cutter head. ( lift the cutter head as you loosen the screws there is barely any room for the screw to go down).
7. Remove the cutter head ( careful don\'t get cut with the blades).
8. Remove pulley.
9. With a bearing puller remove both support bearing and bearing.( now is the time to upgrade your cutter head like I did)
10. Press both bearings and follow everything in reverse order to assemble back.
11. Enjoy your new parts.
Read less
Did you find this story helpful?
Thank you for voting!
Bad ball bearing on cutter head
Daniel from Shelby, Iowa
0 of 1 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
1.) Loosen pulley belt.
2.) Remove belt.
3.) Loosen shaft set screw located on pulley.
4.) Remove pulley from shaft
5.) Remove shaft and bearings assembly from drill press assembly.
6.) Remove snap rings retaining bearings and bearing spacer to shaft.
7.) Remove bearings and spacer from shaft.
8.)
... Read more Assemble in reverse order using new bearings.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9871915
Manufacturer Part Number: 089210136012
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
