Genuine Oster Pro replacement part, this product is sold in a set of two. It also includes the Brush Springs. It is used on the Clipper models shown below. Replacing brushes can fix a motor that's operating intermittently. Carbon brushes are one of the most commonly replaced power tool parts. A worn-out brush will often be worn down and can be cracked, pitted, or burned. If a Brush is burned or scored, it is advised to inspect the armature and field for damage.
Troubleshooting
This part works with the following brands:
Oster
Part# 42584025000 replaces these:
42584025000,
★
Customer Part Reviews
?
4.8
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
5 stars
3
4 stars
1
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Great
Came promptly and quality product
Guest - April 28, 2019
Verified Purchase
★★★★★
★★★★★
Exactly what we ordered
Came quickly and was the right part needed for the job. Thank you
Guest - July 24, 2019
Verified Purchase
★★★★★
★★★★★
Very easy and fast
The ordering process was extremely easy. The prices were very reasonable and the parts were shipped right away. Will buy from them again!!!
Guest - February 23, 2021
Verified Purchase
★★★★★
★★★★★
There are the good replaced parts .
I've received the right parts as needed, but the 10 packs of springs and bruhes set. There are missing 2 pairs of brushes, in this 2 packs packed springs only. Thanks any way.
Guest - July 3, 2019
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Easy
15 - 30 mins
(11 rated repairs)?
< Prev
1
2
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
The blade assembly was worn and not holding blades securely. The clippers are about 2 yrs olde just need a cleaning a lil overhaul
No special instructions needed for installation.. It\'s nice that ereplacements has a diagram of the model... It could be a bit clearer but it did work.. I\'ve had to use this site 3 or four times it is very useful.. I make money with my clippers it\'s good to be able to repair on my own and get back to business..
Take top cover off by removing 2 screws, remove lever, clean out old grease, re-grease, install washer and lever, replace cover, remove brushes one at a time, replace, apply AC, and starts every time. Have less clatter then before therefore I may need another internal part, will investigate at a later time.
Did you find this story helpful?
Thank you for voting!
Wife dropped her clippers and broke the housing and the brushes.
Took the brushes out. Removed end piece, and the clipper head, then pulled armater and inside of clippers out. Replaced housing put armater back in housing, put clipper head and switch housing back on,put brush assembly back in and test runned. worked just fine.
Removed switch cover nut with pliers and cover plate with small phillips screwdriver, took a few pics for reference of wire placement. Removed two screws that held wires and removed switch and cord. Reversed that process and repair was finished. Replaced brush and spring assemblies and lubed clippers while on repair bench. Very simple rep
... Read moreair and saved around $100 plus downtime.
Unscrewed small caps that were over the bushes, removed the old worn out brushes dropped in the new brushes, and screwed the caps over them down snug..clippers are running like new.
Removed both brush spring assemblies from either side, replaced them. Should have done this first, but didn\'t know what a brush spring assembly was until I you tubed it. Unfortunately this was after I replaced the power switch. Overall, didn\'t need to take the whole thing apart, so I was pleased with myself!
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
