This is an original manufacturer sourced replacement part designed for use with Dewalt compound miter saws. It allows you to lift and lower the saw. This item is made out of plastic and it is sold individually. Includes both sides of the handle. Please note the screws used to attach it and the carrying handle are sold separately. You would need a screwdriver for this repair • First you would remove the screws from carrying handle and remove it • Then, remove the screws in the top handle half and remove it • Remove the switch from the bottom half of the handle • Remove the cord clamp that is held in by two (2) screws. • Remove the bottom handle half from the saw by removing the screws holding it to housing • Attach the new handle following the previous steps in reverse
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Exact fit. The part I was looking for.
Part arrived quickly and packed very well. Perfect fit.
Guest - April 29, 2019
Verified Purchase
★★★★★
★★★★★
Fit Great
I broke the trigger handle on my Dewalt chip saw. This is the only place I found it at a reasonable price. Delivery was faster than expected as well. Win win!
Guest - May 3, 2019
Verified Purchase
★★★★★
★★★★★
Great product, a bit pricey though.
Great product, a bit pricey though.
Guest - June 5, 2019
Verified Purchase
★★★★★
★★★★★
Great product
Thought we would have to discard our saw when the handle broke. Very excited to find a replacement part. Great service, handle fits well and we are back in business! Thanks so much for your service!
Guest - June 17, 2019
Verified Purchase
★★★★★
★★★★★
Everything was great!
So easy to use this website. Part came early and fit perfectly. The repair video was great. You guys are doing things right. Will use again.
Guest - September 18, 2019
Verified Purchase
★★★★★
★★★★★
Seamless repair. Finished product looks original.
Part arrived quickly and was easy to replace
Guest - June 5, 2020
Verified Purchase
★★★★★
★★★★★
Always fits
Handle breaks? If not for ya'll it would have been in the trash.
Guest - August 5, 2020
Verified Purchase
★★★★★
★★★★★
Very easy repair
The part fit like a glove it was in good condition. Now my chop saw is back up and running.
Guest - April 8, 2021
Verified Purchase
★★★★★
★★★★★
Works as expected and quick shipping
Saved a couple of hundred dollars replacing parts instead of repurchasing a new say.
Guest - February 1, 2022
Verified Purchase
★★★★★
★★★★★
Saw handle
If fit perfectly and receive it I a couple of days
Guest - April 8, 2022
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
To install the new handle. First remove the screws from carrying handle and remove the handle. Then remove the screws in the top handle half and remove it. Remove the switch from the bottom half of the handle and also remove the cord clamp that is held in by two screws. Then remove the bottom handle half from the saw by removing the screw
... Read mores holding it to housing. Reverse the tear down assembly and your done.
Remove the screws from the carrying handle
Remove the screw from the top switch handle
Remove the bottom switch handle and switch and cord clamp
Install the new bottom switch handle half, with the cord and switch and cord clamp
Install the top switch handle half
Install the new carrying handle
First remove the screws from the carrying handle and set the screws aside. Remove the screws from the top handle, then remove the cord clamp and the switch. Remove the bottom handle from the housing and replace it with the new one, replace switch and cord clamp, then, install the top handle. Then install the carrying handle. Very easy to
... Read morerepair with a screwdriver everything fit perfectly
1- took picture of wiring diagram with phone
2- removed all old screws and mapped them out to what spots they went to. Make sure you make note of where they come from. There are 7 different screws to do this. Used a #15 star bit.
3- disconnect wires from trigger assembly and remove wire clamp
4- remove bottom piece of ha
... Read morendle assembly
5- route all wires from the saw through the base of new handle
6-place power cord at back and reconnect the trigger assembly and route all wires according to the picture or wire diagram
7- screw it all back together using the map you made of where the screws go-note: screw handle to saw first before screwing the handle together
Read less
Did you find this story helpful?
Thank you for voting!
Handle on Dewalt compound Mitre Saw broke after falling over.
Removed broken trigger assembly and handle. Disconnected electrical wiring. Installed new handle assembly and retired trigger with absolutely no problems.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
