This metal driver pulley is used in Murray lawn tractors. It is a replacement part directly sourced from the manufacturer. This part is sold as an individual replacement. The drive pulley applies force to the motion drive belt, which is wrapped around this part. A wrench and pliers may be needed for the replacement of the pulley when it becomes worn or cracked.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Murray tractor parts
Always satisfied when ordering parts, must say hard to find parts. Understand situation we are all under now, must have a little patience on shipping time
Guest - July 5, 2020
Verified Purchase
★★★★★
★★★★★
Murry Drive Pully
Part came quickly, fit correctly, was good quality. Was not an easy repair, but that was fault of manufacturer, not the replacement part.
Guest - May 11, 2021
Verified Purchase
★★★★★
★★★★★
Worked as expected
Original Drive Pulley was worn out & beginning to wobble a bit, but after 23 years of service....what would you expect! New pulley works fine and I'm back to mowing again.
Guest - May 11, 2022
Verified Purchase
★★★★★
★★★★★
Shipping seemed high for the weight
I have bought many items from e-replacement parts. the shipping seemed fair. this pulley didn't seem to be very heavy to warrant such a fee. the repair was successful and complicated. The trans axle had to come out in order to route the belt. three against a thousand---the toughest three ever fought.
Bruce - September 2, 2025
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
After wasting time trying to put the belt back on the transaxle pulley I realized the pulley was trashed (the center hole was completely wallowed out) and I was missing the snap ring that holds the pulley at the proper height. I dropped the mower deck, jacked up the rear end placing jack stands under the mower and pulled off the rear whe
... Read moreels. Then I disconnected the brake and shifter rods and removed the 5 bolts securing the transaxle and lowered it on the jack. It was very easy to install the new snap ring and pulley. The belt was in great shape so I stayed with it. I bought a new pulley for the clutch and replaced it at the same time. While my pulley was ok I figured since it was only a little more than 10 bucks I\'d change it out and I hope to be done with a future repair as the machine is 14 years old. Special instructions would be \"you have to hold the clutch/brake pedal down while placing the drive belt\" and don\'t forget to loosen those two rods that are supposed to keep the belt from coming off the drive pulley. They will keep you from putting a belt on if not slackened and moved away for placement.
Read less
Did you find this story helpful?
Thank you for voting!
Pulley had rusted away, so no drive system operation
1. Removed the axle from the tractor.
2. Cleaned/washed off the axle to remove dirt and debris.
3. Used 3 inch cutoff wheel and made a 2 inch square of pulley at the shaft area.
4. Used a 3\" pitman/tie rod puller to remove the pulley collar and remains from the shaft.
5. Cleaned shaft and applied anti seize to the
... Read more shaft.
6. Installed new pulley, snap ring.
7. Reinstalled axle and replaced belt.
1. Removed the battery.
2. Took the back plate off the mower.
3. Loosened four bolts holding the rear assembly to the mower.
4. Lifted the mower off the rear assembly.
5. Replaced the old drive pulley with the new.
6. Replaced the lock washer.
7. Reattached the belt.
8. Reattached the rear assembl
... Read morey and the rear plate.
9. Replaced the battery.
Read less
Did you find this story helpful?
Thank you for voting!
Some how the collar on the pulley got damaged destroying the keyway. I had to replace both items to get the lawnmower to stop making noises
The transmission had to be removed from the lawn mower, it was easy only 4 small screws held it to the frame. The pulley was held on the shaft by a snap ring.
The drive pulley I ordered for my old hand me down Murray riding lawn mower was a perfect fit . It was a certified Briggs and Stratton part. Which Murray has been out of business for years so when i called around I was told Murray parts have been discontinued. The other review for this part said only 4 bolts to drop the transmission and m
... Read moreount Pulley. Not true on my model.....some of the bolt locations were very difficult to loosen. So taking the battery out and removing the rear tow plate made it possible. I broke one old rusty bolt and the pulley snap ring and shaft had become one with rust...due to the fact it sat outside for 5 years. I had to cut the pulley into quarters like a pie with a grinder cutting wheel to remove from shaft. I created a snap ring using a zinc washer. The good news was that the pulley fit perfectly snug and the mower is running smoothly now with new drive pulley and belt. !!!! I couldn\'t be more satisfied...35 dollars total ( included shipping) I hope your machine isn\'t as rusty as mine good luck !
Drop rear end, removed retaining ring, removed old pulley put e-ring in place put on new pulley put new retaining ring reinstalled rear end and drive belt.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_5.gif "Part Location Diagram of 95094MA Murray Pulley - Low Noise")
_WW_5.gif "Part Location Diagram of 95094MA Murray Pulley - Low Noise")
