This throttle box ass\\\'y is an OEM direct from the Ryobi manufacturer. This item is constructed of plastic and metal parts, and is compatible with many tiller devices. The throttle box assembly is fastened onto the r.h. upper handle. Please refer to specific manual and diagrams for repair instructions. This part is sold individually. A screwdriver is needed in the replacement.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
throttle control knob
Perfect fit. Better than the original by a long shot.
Guest - May 15, 2019
Verified Purchase
★★★★★
★★★★★
Easy reapair
better than original part
Kerry - June 3, 2019
Verified Purchase
★★★★★
★★★★★
Just what I needed
Arrived on time
Guest - July 1, 2019
Verified Purchase
★★★★★
★★★★★
No qualms
I received the parts they were all correct and in a timely manner I will use the site again maybe a tad bit more than I wanted to pay but I can't complain everything was correct and no problem with the parts
Guest - January 30, 2020
Verified Purchase
★★★★★
★★★★★
easy repair
the covid 19 virus interfered slightly with delivery but everything was as expected and my roto tiller is back in working order thank you
Guest - April 16, 2020
Verified Purchase
★★★★★
★★★★★
Throttle bracket
Good quality, easily installed, would recommend
Don - May 20, 2020
Verified Purchase
★★★★★
★★★★★
Easy ordering
It was easy to identify the part I needed from the parts diagram. I was a little concerned I wouldn't be able to find the part I needed since the tiller is so old. No problems at all. Shipped out quickly and good communication on tracking the status.
Guest - March 30, 2021
Verified Purchase
★★★★★
★★★★★
Worked Great
Received the part within a few days of ordering. Part was as described and works great.
Guest - June 22, 2022
Verified Purchase
★★★★★
★★★★★
Good quality
Only wish that there were instructions with it. There seems to be maybe a part not included
Guest - April 4, 2023
Verified Purchase
★★★★★
★★★★★
Bad shipping
Hopefully the parts will work! I have installed them waiting for the rain to go away to see if it works! What upset me about this order was the shipping! I was sent an email saying it shipped I looked at the shipping info and it didn’t show shipped but your site did! I made at least 3 calls over a few days to try and find out about the order and was basically given the run around!! Finally on the day it showed it was going to be delivered to me I called again and that person said I had to wait like 5 days and call if I hadn’t received my order! Interestingly after I gave him my opinion / frustration of the issue and after we hung up I received an email that my items were on the way! Imagine that! Ridiculous!
Carol - March 28, 2020
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Removed the old throttle box from the handle
Removed the throttle cable from the throttle handle
Installed the cable to the new handle
Placed the washers in the new throttle box with the handle and cable
Installed the new box on the handle
Worst part was getting old one out. Had to break it apart to get cable out. Then get it all lined up and use pliers to get pins together. Part arrived quick and was much better than part that came on the tiller. I bought it about 35 years ago so I was amazed to be able to get the part I needed. Thanks
Did you find this story helpful?
Thank you for voting!
Throttle was broke off of dash. And bushing was totally gone from front wheel.
1. Use a floor jack to raise front of tractor.
2. Pull plastic cap off. Use pliers to remove carter key from axle. Wheel should slip off. If not
turn wheel & tap with hammer to remove.
3. Replace bushing in wheel and clean axle with wire brush. Little grease here wouldn\'t hurt.
4. Slide wheel with new bushin
... Read moreg back onto axle. Replace carter key and cap.
1. Throttle body is two bolts/ screws . Remove screws ,hook old cable into hole of handle. Put
sides back together replace screws.
2 Stick cable though dash till housing snaps into dash. Mine had a screw to mount housing to
dash.
3. Hook wire/cable into linkage and replace set screw to hold cable in place.
Removed screw holding throttle box , popped it up and out. Removed two screws holding box together. Separated box halves unhooked cable. Then reversed the steps.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9157739
Manufacturer Part Number: 831-0823A
Lawn Mower
- MTD Lawn Mower Model 06-449714 (06449714, 06 449714) Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Circuit Board or Touch Pad","title":"Circuit Board or Touch Pad","url":"/parts/lawn-and-garden/lawn-tractor/circuit-boards-and-touch-pads/"},{"position":2,"name":"831-0823A","title":"831-0823A","url":""}]
_WW_1.gif "Part Location Diagram of 831-0823A MTD Control Box-thrott")
_WW_1.gif "Part Location Diagram of 831-0823A MTD Control Box-thrott")
