This is an authentic Snapper replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The shift handle is used as a lever that changes the gear that the mower is running with. The handle is priced as a single item, please note the knob is separate.
Troubleshooting
This part works with the following brands:
Snapper
Craftsman
Murray
Briggs and Stratton
This part works with the following products:
Lawn Mower
Lawn Tractor
Part# 7059212DYP replaces these:
7059212BMYP, 7059212DYP, 7059212YP,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
THE PART MATCHED THE AD
PART FIT THE MOWER AND WORKED
Guest - July 10, 2021
Verified Purchase
★★★★★
★★★★★
Shift Handle Replacement
The replacement shift handle was exactly like the OEM handle that came on the Snapper 10hp - 28" riding mower. Works and looks great.
Guest - October 12, 2021
Verified Purchase
★★★★★
★★★★★
Snapper Rider
My snapper riding mower is over twenty years old and still running strong.
When the shift handle weld broke and I needed a replacement part , with it being so old , I thought that I would never be able to find the correct part that I needed.
I found what I was looking for on the eReplacementParts website.
I was an exact fit and not overly priced far cheaper that buying a new mower.
Guest - August 5, 2023
Verified Purchase
★★★★★
★★★★★
Snapper shift handle was an exact match
Pulled cotter pin first’ and compressed spring
With a 6” C clamp to replace broken shift handle. Took about 20 minutes .
Shifts great! They were the only ones that had this part!
Guest - September 9, 2023
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
A Bit Difficult
30 - 60 mins
(12 rated repairs)?
< Prev
1
2
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
I used a 6in clamp to compress the spring g, removed cotter pin with pliers, used a punch and hammer to remove the pin.I then removed all the rust from the pin and sprayed the pin and hole with wd40. put the new lever in place e, drove the pin in place, used the cotter pin to hold assembly together.put on the rubber grip and removed the c
... Read more-clamp.
Tapped block in place, to take pressure off spring-loaded shift handle. Pulled cotter pin out of retainer pin. Tapped retainer pin out, with punch. Removed old handle, replaced with new one. Re-installed retainer pin then new cotter pin.
I have a Snapper 30\" 11 HP rear-engine mower and the shift link from the transmission to the bell crank broke, along with the gearshift lever (right above the gear position plate). The shift link went on with no problem (though it\'s tight getting too it), but I ended up having to grind both ends of the pivot pin off so I could get the l
... Read moreever removed then drilling out the pivot pin that holds the shift lever to the shaft. It just didn\'t want to come out, even with some very heavy \'persuasion\'. That sucker was IN THERE! Big pain. It took a little over an hour, but would have been a 20 minute job, but for the drilling the pivot pin out.
Parts from ereplacementparts went on no problem. Rapid delivery and great prices! My one-stop source for lawn equipment repair items!
Read less
Did you find this story helpful?
Thank you for voting!
The mower gear shift broke
Doug from Maryville, Tennessee
0 of 1 peoplefound this instruction helpful.
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Noticed the axle boots broken, so I felt the problem mite be that dirt was causing the extra strain on shift handle. Replaced the parts that I got from ereplacementparts. All fit perfect and now it shifts and drives great. Thanks
Remove old lever from the base and replace with a new one.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
