Part Location Diagram of 951-10309 MTD Carburetor Asm
See part A14 in the diagram
( Grid squares measure 1x1 inch )

Carburetor Asm 951-10309

Manufactured by:
MTD
ERP Number:
ERP9169378
Part Number:
951-10309
Original Equipment Manufacturer ?
  Works with your model  1P65!
$122.00
In Stock
Delivers in 3-5 Business Days!

Easy 

15 - 30 mins 

(4 rated repairs) ?
  Works with your model   1P65!

Product Description

?

This is a genuine OEM sourced part which is specially designed for use with MTD and Yard Man lawn and garden equipment. The purpose of a carburetor is to mix the air and the gas before the combustible mixture goes to the engine. If the engine won\\\'t start and the tank is full of fresh fuel or if the engine starts and then quickly dies, the carburetor is likely the problem. This high-quality assembly is sold individually, keep in mind it includes a durable metal body carburetor and the gaskets to ensure an air-tight seal. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component.

Troubleshooting

This part works with the following brands:
  • MTD
  • Yard Man
  • Troy-Bilt
  • Cub Cadet
  • Yard Machines
This part works with the following products:
  • Lawn Mower
  • Engine
Part# 951-10309 replaces these:
751-10309, 951-10309,

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

15 - 30 mins 

(4 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Carburetor float had a hole in it.

john from Hudson, Ohio

3 of 3 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
951-10309
1. Disconnected the lines.
2. Removed the old carburetor.
3. Attached the new carburetor.
4. Reattached the lines and tested.
Did you find this story helpful?
Thank you for voting!

Yard Man lawn mower wouldn\'t start

Curtis from HENDERSON, Nevada

2 of 2 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
951-10309
A. Lawn mower would run spraying starting fluid into carb.
B. Took original carb apart and cleaned - no go, couldn\'t get the jets out.
C. Replace carb.

1. Drain fuel tank - squeeze ball type siphon from Pep Boys
2. Remove air filter assembly - 2 nuts 1 bolt (10mm socket)
3. Remove spring clamp from the fuel line at the carb
4. Disconnect governor spring from the throttle plate - don\'t lose it.
5. Hold the throttle plate open and pull up to remove the linkage
6. Slide carb off - take note of the gasket(s) order and orientation, unhook the choke linkage
7. Remove remaining gasket assemblies and again take note of the gasket(s) order and orientation - this is the most important part.
8. Clean up the mounting surface on the cylinder - don\'t scratch it up.
9. Install new gaskets and new carb in the reverse order above
My mower started on the 1st pull
Did you find this story helpful?
Thank you for voting!

old carb was all gooped up

Robert from LIVINGSTON, Texas

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set
Parts Used:
951-10309
Replaced Carb with new one
Did you find this story helpful?
Thank you for voting!

No fuel reached the carb. Needles blocked

William from Utica, New York

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
951-10309
Remove old one and replace with new one. It was that simple
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP9169378
Manufacturer Part Number: 951-10309
Brand Model Number Description
MTD 11A-08MB000 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB002 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB006 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB009 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB016 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB019 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB022 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB026 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB029 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB031 Lawn Mower - Gas Walk-Behind Mower
MTD 11A-08MB033 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB054 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB057 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB077 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB098 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB105 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB118 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB121 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB129 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB131 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB134 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB138 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB145 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB151 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB196 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB205 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB206 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB229 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB301 Lawn Mower - Push Walk-Behind Mower
MTD 11A-08MB304 Lawn Mower - Push Walk-Behind Mower