Weed Eater Trimmer Carburetors

This is a genuine OEM replacement part, it is sold individually. By pressing on the Purge Bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. Over time the primer will lose its elasticity or crack and need to be replaced. We have an article and video on

This is a genuine manufacturer-sourced replacement gasket repair kit that is specially made for use with Paramount and Poulan lawn and garden equipment. It is utilized to replace carburetor gaskets and diaphragms that were originally installed on a new unit. If you have a problem with your carburetor this will usually take care of it. Keep in mind this high-quality kit is sold individually. Please...

This is a Genuine OEM rebuild kit designed for Walbro Carburetors. This kit contains all the necessary Gaskets and Diaphragms needed to rebuild your carburetor. If your engine runs sluggish or it dies shortly after starting it, you may need to rebuild your carburetor. Replacing these items you would need a Screwdriver and Pliers.

This is an authentic OEM part. The metering diaphragm is a Walbro part that is used inside of carburetors that work with small engines. This part goes between the carburetor body and the fuel pump. This diaphragm is used to help regulate the fuel to maintain the proper air/fuel ratio. This part is priced as a single item.

This part is available as an individual replacement part. The carburetor adapter attaches to the gasket. During replacement, it may require an allen wrench to help install this part correctly. It is made of plastic and will require replacing if it breaks. This genuine item is supplied by the original equipment manufacturer for use with Poulan and Weed Eater trimmers.

This is a genuine OEM sourced rebuild kit is designed for gas trimmers/blowers. This kit contains all the necessary parts to rebuild your carburetor. It includes: primer bulb, the float, needle, gaskets, seals needed to repair or refurbish a carburetor. Replacing these items you would need a screwdriver and pliers.

This metering diaphragm is an original part for use in edgers, blowers, trimmers, and chainsaws made by Poulan, Paramount, Weed Eater, Husqvarna, and Jonsered. It fits between the metering diaphragm gasket and the metering diaphragm cover. It is made of a thin material and will need to be replaced if it breaks. A screwdriver may be needed when replacing this part and keep in mind that it is sold individually.

Genuine OEM replacement part, this part is sold individually. A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotati...

This carburetor repair kit is supplied by the original manufacturer for use in trimmers. The kit includes the diaphragm and carburetor gaskets, strainers, primer bulb, inlet needles, springs, and pins. It is normal for gaskets to wear down, brittle, or lose their sealing ability over time due to exposure to fuel, heat, and pressure. Faulty gaskets can result in loss of compression, inadequate lubr...

This is an authentic OEM sourced component which is specially made for use with gas-powered lawn and garden equipment. The part provides an identical replacement for a missing or a worn diaphragm that was installed on a new unit. It is provides a tight seal for the fuel pump. Please make sure to refer to the appropriate diagrams of your model for the correct repair procedure. Keep in mind this hig...

This replacement carburetor is sourced from original equipment manufacturer for use with Weed Eater gas trimmers/edgers. The purpose of a carburetor is to supply a combustible mixture of fuel and air to the engine. It has a metal body and a rubber primer bulb. Please note gaskets are sold separately. To complete this repair you would need a hex key/allen wrench. • Remove air box cover and base...

This is a manufacturer approved replacement part used on gas trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won\\\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the ...

This is an original replacement part manufactured for use with gas powered trimmers. The carburetor is used to mix air and fuel to send to the motor's combustion chamber. This carburetor is a complete part assembly and is available as an individual replacement part.

This is a genuine manufacturer-sourced kit which is specially designed for use with Poulan and Weed Eater handheld trimmers. This kit contains all the necessary gaskets, diaphragms and other parts necessary to rebuild your carburetor. It helps to fix common problems associated with worn out gaskets or diaphragms, including leaks, sluggish performance, and other carburetor related issues. Keep in m...

This is an authentic OEM sourced replacement component which is specially designed for Poulan and Weed Eater handheld lawn and garden equipment. It fits between the carburetor and the cylinder, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this item. Over time it may wear out, get damaged or simply lost eventually requiring a replac...

It is a genuine item which is supplied directly from the original equipment manufacturer for use with Weed Eater trimmers. The purge bulb allows a user to pump the fuel into the carburetor, once it is full the excess fuel is sent back to the tank through the return line. Keep in mind this high-quality item is sold individually, it includes a durable rubber bulb with a metal shaft.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with trimmers and pruners from Poulan and Weed Eater. The choke lever includes the valve plate and is used to restrict the flow of air sending a richer fuel/air mixture to the combustion chamber when cold starting the engine. This item is available as an individual replacement part.

This authentic gasket kit is supplied directly from the original equipment manufacturer for use with Weed Eater handheld trimmers. Unfortunately, over time parts may wear out and begin to crack eventually requiring replacements. The repair kit contains all the recommended parts needed to fix your carburetor. Refer to the owner's manual and the appropriate diagrams for your model to ensure the corr...