Murray Trimmer Parts

Murray Appliance Parts

We sell only genuine OEM Murray ® parts.

Top Murray Trimmer Models

See All Models

Popular Murray Trimmer Parts

Manufacturer Part Number:
753-06183
This OEM fuel tank assembly is made out of Plastic and it includes the fuel lines, fuel cap, and fuel filter. It is a common part in gas trimmers that is used to hold the fuel needed for the engine. It is very important to replace the fuel tank if it is cracked or damaged to avoid further damage or serious injuries. Make sure to drain the gas tank before starting a repair.
Manufacturer Part Number:
791-153066B
Carburetor O-ring
★★★★★
★★★★★
(8)
$4.13
In Stock
Minimum Quantity of 2 required
Manufacturer Part Number:
753-06185
This is a manufacturer approved O-Ring designed for lawn and garden equipment. This is the O-Ring that provides an Air Tight seal between Carburetor and Cylinder Head. If doing maintenance on carburetor it is recommended to replace the O-Ring instead of re-using the old one. Over time rings and seals tend to dry out and would no longer provide proper seal compromising engines performance.
Manufacturer Part Number:
753-06847
This is a genuine OEM sourced part which is specially made for use with Craftsman handheld lawn and garden equipment. Its purpose is to deliver electric current from the ignition system to the combustion chamber. It will ignite the air fuel mixture by the spark. Unfortunately, over time a spark plug can wear out or it may get damaged eventually requiring a replacement to ensure peak performance. K...
Carburetor Gasket
★★★★★
★★★★★
(16)
$4.13
In Stock
Minimum Quantity of 2 required
Manufacturer Part Number:
753-06253
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with trimmers and blowers. The gasket is used to seal the connection between the carburetor and the air cleaner assembly. It is recommended to replace gaskets when servicing the motor to ensure proper seals when the parts are reassembled. This item is available as an individual replacement part.
Manufacturer Part Number:
753-06417
This is a genuine OEM replacement part designed for use with some Handheld String Trimmers. This filter is made out of Foam and it is sold individually. The purpose of this filter is to keep dirt and other small particles from entering the carburetor and engine and causing internal engine damage. Once this type of filter gets clogged or dirty it should be changed (Not Cleaned). This is to prevent ...
Manufacturer Part Number:
791-683974B
This is a genuine OEM approved replacement part, it is specially designed for use with Craftsman gas powered lawn and garden equipment. By pressing on the purge bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. Over time the material may begin to deterio...
Manufacturer Part Number:
753-1155
This spool is for line trimmers. Spool houses the cutting line and fits inside the cutting head to cut grass and weeds. Wear work gloves to protect your hands when installing this part.
Manufacturer Part Number:
791-610317B
Genuine OEM replacement part, this item is sold individually. This spring is used on all of the trimmers listed below. It is installed between the inner reel and the outer spool assembly. Its purpose is to keep pressure on the Bump Head Knob Assembly.
Manufacturer Part Number:
753-05860
Genuine OEM replacement kit used on Gas Trimmers and Tillers. This part includes: Clutch Drum, Clutch, Clutch Washer and the Screw which has a left-handed thread. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point...
Manufacturer Part Number:
753-08170
This authentic component is supplied directly from the original equipment manufacturer for use with MTD string trimmers. It is an identical replacement for a missing or a faulty glide cap that was installed on a new unit. The cap is secured on the bottom of the cutting head assembly, please make sure to refer to the appropriate diagrams of your model for the correct location and application of thi...
Manufacturer Part Number:
753-08169
This is an authentic MTD replacement part manufactured for use with gas powered trimmers. The special cutting head assembly is a complete replacement part that includes the string housing, cap, and hardware. This cutting head assembly is available as an individual replacement part, please see model diagram for associative parts.

Murray Trimmer Models