Jonsered Trimmer Carburetors

This carburetor mixes air and fuel to power small engines, helping ensure smooth starting and reliable performance. Built from durable materials, it supports consistent fuel delivery and efficient operation. Replacing a worn or faulty carburetor can resolve issues such as hard starting, rough idling, or poor acceleration, restoring proper engine function.

This is a genuine OEM sourced replacement part used on Husqvarna trimmers and brushcutters. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then ...

This is a genuine manufacturer-sourced replacement gasket repair kit that is specially made for use with Paramount and Poulan lawn and garden equipment. It is utilized to replace carburetor gaskets and diaphragms that were originally installed on a new unit. If you have a problem with your carburetor this will usually take care of it. Keep in mind this high-quality kit is sold individually. Please...

This is a genuine OEM part. The Husqvarna choke control is made for use with many lawn and garden trimmers. The plastic component is fastened to the carburetor, allowing the operator to manage the engine's fuel and air mixture. A hex key and a wrench may be required for making the repair. The choke control is sold individually.

This is an authentic Husqvarna replacement part manufactured for use with trimmers and brush cutters. The carburetor adapter is used to connect the carburetor to the cylinder. The carburetor adapter is available as an individual replacement part, please note the gaskets are available separately.

This is a genuine OEM sourced rebuild kit is designed for gas trimmers/blowers. This kit contains all the necessary parts to rebuild your carburetor. It includes: primer bulb, the float, needle, gaskets, seals needed to repair or refurbish a carburetor. Replacing these items you would need a screwdriver and pliers.

Carburetor Kit

This is an original Husqvarna replacement part manufactured for use with trimmers and brushcutters. The plastic choke lever is used to actuate the choke valve to limit air entering the engine when cold starting the machine. This choke lever is available as an individual replacement part, please see model diagram for associative parts.

This metering diaphragm is an original part for use in edgers, blowers, trimmers, and chainsaws made by Poulan, Paramount, Weed Eater, Husqvarna, and Jonsered. It fits between the metering diaphragm gasket and the metering diaphragm cover. It is made of a thin material and will need to be replaced if it breaks. A screwdriver may be needed when replacing this part and keep in mind that it is sold individually.

This is an authentic OEM sourced component which is specially made for use with gas-powered lawn and garden equipment. The part provides an identical replacement for a missing or a worn diaphragm that was installed on a new unit. It is provides a tight seal for the fuel pump. Please make sure to refer to the appropriate diagrams of your model for the correct repair procedure. Keep in mind this hig...

This is an authentic Husqvarna replacement part manufactured for use with handheld outdoor power equipment. The carburetor diaphragm acts as a membrane that actuates the inlet needle valve to meter the amount of fuel let into the carburetor. Over time the soft rubber parts of the carburetor can seize up restricting the fuel flowing through the carburetor. This diaphragm is available as an individu...

This genuine replacement carburetor assembly is designed for Husqvarna gas powered edgers/trimmers. Carburetor supplies a combustible mixture of gas and air to the engine. It also helps to control its speed. This kit includes a metal body carburetor and a composite material gasket. To complete this repair a screwdriver would be needed. • Remove the air box cover, filter and base • Remove the...

This is a genuine manufacturer-sourced kit which is specially designed for use with Poulan and Weed Eater handheld trimmers. This kit contains all the necessary gaskets, diaphragms and other parts necessary to rebuild your carburetor. It helps to fix common problems associated with worn out gaskets or diaphragms, including leaks, sluggish performance, and other carburetor related issues. Keep in m...

It is a genuine item that is supplied by the original equipment manufacturer for use with Husqvarna chainsaws. This is an identical replacement for a missing or a faulty inlet needle that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made o...

This is a genuine part which is supplied directly by the original equipment manufacturer and is used with Husqvarna hedge trimmers. The carburetor mixes air and gas before the fuel mix goes to the engine. This part is made of metal and plastic and is also sold individually. Let the engine cool and drain the gas tank before starting this repair. You may need screw drivers and pliers to aid you in this repair.