Simplicity Snow Blower Hardware

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure...

This is an authentic replacement part for use with outdoor power equipment. This versatile metal lock washer has many applications for use with products like tillers, snowthrowers, and lawnmowers. The washer is sold individually, please see model diagram for part usage.

This is a genuine OEM sourced replacement shear pin designed for use with snow blowers/throwers. Shear pins are installed in order to protect your snowblower and it measures 1/4 X 1.750. If the auger gets jammed or clogged, shear bolt is designed to snap at a certain point of pressure, so it will not damage any other part of the unit. This pin is made out of metal and it is sold individually. Plea...

This is an OEM part sourced directly from the manufacturer. The nut is commonly found in lawn tractors and snowblowers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different nuts used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replaci...

This is a genuine Murray replacement part, it is sold individually. It is commonly used in lawn tractors, and is used in various places in the compatible models listed below. It is self tapping, with a 9/16 hex head. Made of metal.

This is a genuine OEM sourced replacement part designed for use with Murray lawn and garden equipment. This is a standard hardware which has multiple applications based on your unit. Please refer to diagrams of your equipment for correct application. This item is made out of metal and it is sold individually.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The metal washer is used to provide spacing between the steering spindle and the front axle assembly. This item is sold individually, please note two washers may be needed.

This is a genuine manufacturer-sourced part which is specially designed for use with Murray, Snapper and Simplicity lawn and garden equipment. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This is standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and applicati...

This item has been sourced from the original manufacturer to be used with lawn tractors from Murray. The metal washer is used with different types of mowers and the application of the washer can vary based on the model of the machine. This washer is sold as an individual replacement part.

The metal flat washer is priced individually. It attaches to the cast iron axle along with the bolt and the bearing. A set of pliers, a screwdriver, and a wrench may be necessary during the installation of this item. This is an original part for Murray lawn tractors and Snapper rear engine rider mowers.

This is a genuine OEM sourced replacement part for Lawn and Garden equipment. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. It will have different applications based on your equipment. Please refer to diagrams for proper use. This item is metal an is sold individually. You would need a wrench to tighten/loosen this nut.

This is a genuine OEM sourced replacement hardware designed for use with snowblowers. Shear bolts are installed in order to protect your unit. If the auger gets jammed or clogged, shear bolt is designed to snap at a certain point of pressure, so it will not damage any other part of the unit. It is made from metal and it is sold individually. You will need a wrench to remove or install this bolt.

This authentic OEM sealing washer is designed for your lawn equipment to create a tight seal within the carburetor body, preventing fuel or air leaks. If you notice any signs of leaks, such as dripping fuel or hissing sounds, it may indicate a faulty or worn-out sealing washer. Additionally, you might be experiencing engine performance issues like rough idling or difficulty starting. To replace th...

This is an authentic OEM sourced replacement component which is specially made for use with Craftsman lawn and garden equipment. It is a standard hardware which has multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this item. Keep in mind this high-quality hex nut is made of durable metal and is sold individually.

This is an original replacement part manufactured for use with Craftsman snow throwers. The special bolt is used to secure the auger blade to the axle. The bolt is used as a safeguard if the blade gets caught or stuck the force will snap the bolt rather than breaking more expensive parts like the auger transmission. The bolts are sold in pairs and include the nuts and washers, the bolt sets are so...

This is an authentic carriage bolt is designed for use with lawn and garden equipment. It is sourced from original equipment manufacturer. This bolt has multiple uses depending on your equipment. Please refer to diagrams for correct use/application of this bolt. The square design under the bolts head is used to fit into a square opening which restrains the bolt and keeps it from turning when the b...

This is an authentic replacement part sourced directly from the manufacturer. The screw is commonly found in snowthrowers and lawn tractors from Murray, Simplicity, and Snapper. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of orderi...

This item is an OEM sourced replacement part that is intended to be used with small engines for snowthrowers and riding lawnmowers. The seal is used as a replacement of an original part from Briggs & Stratton or Toro machines. This item is used to prevent oil or fuel leaks between two different part assemblies. The item can have different applications depending on the model of the engine or machin...