Craftsman Leaf Blower / Vacuum Carburetors

A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to h...

This is a genuine OEM replacement part, it is sold individually. By pressing on the Purge Bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. Over time the primer will lose its elasticity or crack and need to be replaced. We have an article and video on

This is an Authentic OEM replacement part used on Gas-Powered Handheld Gas Blowers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly ...

This is a genuine manufacturer-sourced replacement gasket repair kit that is specially made for use with Paramount and Poulan lawn and garden equipment. It is utilized to replace carburetor gaskets and diaphragms that were originally installed on a new unit. If you have a problem with your carburetor this will usually take care of it. Keep in mind this high-quality kit is sold individually. Please...

Genuine OEM replacement part is made out of Plastic, this item is sold individually. This part is used on the carburetor for gas powered blowers to restrict the flow of air, thereby enriching the fuel-air mixture. Because this part is used quite frequently it has a tendency to wear. To replace it, simply press it on the Choke Shaft of the carburetor.

This genuine replacement part is designed for use with Poulan gas blower. It is sourced from original equipment manufacturer and it is sold individually. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carb...

This carburetor boot fits between the cylinder and the carburetor plate providing an air-tight seal. Over time due to heat and regular wear it may deteriorate and crack eventually requiring replacement to maintain optimum performance. It is a genuine replacement part that is supplied directly from original equipment manufacturer for use with Poulan and Husqvarna lead blowers and trimmers. Please n...

This is a genuine Husqvarna and Jonsered replacement part for use in blowers. The carburetor plate goes between the gasket and the carburetor boot. A screwdriver and a nutdriver may be needed during the replacement of this part. It is made out of plastic and will need to be replaced if it breaks. This item is sold individually.

Carb. adaptor

This metering diaphragm is an original part for use in edgers, blowers, trimmers, and chainsaws made by Poulan, Paramount, Weed Eater, Husqvarna, and Jonsered. It fits between the metering diaphragm gasket and the metering diaphragm cover. It is made of a thin material and will need to be replaced if it breaks. A screwdriver may be needed when replacing this part and keep in mind that it is sold individually.

This is an authentic OEM sourced component which is specially made for use with gas-powered lawn and garden equipment. The part provides an identical replacement for a missing or a worn diaphragm that was installed on a new unit. It is provides a tight seal for the fuel pump. Please make sure to refer to the appropriate diagrams of your model for the correct repair procedure. Keep in mind this hig...

This choke link is an OEM direct from Briggs & Stratton. The metal component is made for use with many small engines. The choke link is fastened between the choke thermostat and the carburetor. This item helps to manage the air flow in the carburetor when the engine is activated. A hex key and a pair of pliers are often needed for the repair. The choke is sold individually.

This is a genuine OEM sourced replacement carburetor, it is commonly installed on Craftsman gas powered backpack blowers. The purpose of this part is to mix the air and the gas before the combustible fuel mix goes to the engine. Often if the engine won't start and the tank is full of fresh fuel, or if the engine starts and then quickly dies, the carburetor is likely the problem. This part provides...

This part is the OEM part from Craftsman used with blowers. This part mixes gas and air before the fuel mix goes to the engine. This carburetor assembly includes the carburetor and two gaskets. You will need a torx screwdriver to replace this part.

This is a genuine manufacturer-sourced part that is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is generally utilized to provide an air-tight seal for the carburetor, please make sure to check the diagrams of your model for the correct location and application of this hardware. Unfortunately, over time gasket material may deterior...

The carburetor fits between the air box and the carburetor adaptor and is made of metal and plastic. It is an OEM from Poulan, Weed Eater, and Jonsered and is used in blowers. This part is available individually and may require a screwdriver during installation. It helps with the fuel mix and can be cleaned if it is causing problems with the engine, but will need to be replaced if it becomes broken.