MTD Lawn Tractor Engines

This is a genuine Toro replacement part. The camshaft is designed by the manufacturer for use in lawn tractors and engines. This part is made of metal, and is placed in the crankcase assembly to interact with the crankshaft. It comes with two metal tappet valves. You may require a wrench when replacing this item. This part is sold individually.

This is a genuine Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with small engines and lawnmowers from Toro. The metal connecting rod is used to link the engine's piston and the crankshaft assembly. This item is sold as a single item.

This gear-governor is a special component that helps to engage the drive shaft. It is a genuine Briggs and Stratton item that is supplied by the original manufacturer for use with small engines that are commonly installed on a variety of lawn and garden equipment. It provides an identical replacement for a damaged or a missing hardware that was installed on a new unit. Check the diagrams for your ...

This is a genuine Briggs and Stratton, Toro part for use with lawn and garden equipment engines. The crankcase breather valve opens to relieve pressure in the crankcase. The most common reason for replacing the breather is when the small engine runs poorly. This part is sold individually. Here is a list of tools that are needed to replace the breather valve a flat-head screwdriver, hammer, 7/16th-...

This is a genuine OEM supplied replacement part that is specially designed for Briggs and Stratton engines that are commonly installed on Toro lawn and garden equipment. It is the part that the piston is attached to. The piston is a central component of a two-cycle engine. It provides both the compression within the engine and it transfers the energy from combustion to the crankshaft which creates...

This is a manufacturer approved replacement part used on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent push rod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately. This part is made out of metal and it is sold individually.

It is a genuine item that is supplied by the original manufacturer for use with walk-behind lawn mowers. The wire rod is utilized to secure the rear trail shield. It is an identical replacement for a missing or a damaged part that was included with a new unit. Refer to the owner\\\'s manual for your model to ensure the correct application. Note, this high-quality wire rod is made of durable metal ...

This piston ring set is used to seal the combustion chamber inside a small engine, helping maintain proper compression and control oil consumption. Replacing worn or damaged rings can improve starting, restore power, and reduce excessive smoke. It is commonly used during engine repairs or rebuilds when performance has dropped due to compression loss.

This authentic manufacturer-sourced part is specially made for use with lawn and garden equipment. The timing gear is an important component of an engine that helps to drive the unit, unfortunately, over time it may wear out or get damaged eventually requiring a replacement. This gear helps to rotate the camshaft, please make sure to refer to the appropriate diagrams of your model for the correct ...

The connecting rod is part of the crankcase assembly. It is a genuine item that is supplied by the original equipment manufacturer for use with Briggs & Stratton engines and Toro lawn tractors. This part is made of metal and is available individually. During replacement, it may require a screwdriver to help install this part correctly. It will require replacing if it becomes broken.

This is a genuine manufacturer-approved replacement push-rod which is used with Briggs and Stratton engines commonly installed on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent push-rod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately. Th...

This is an authentic Briggs & Stratton replacement part manufactured for use with small engines. The ring set is used to seal and separate the cylinder and the crankcase. A damaged piston ring can allow combustion gasses to enter the crankcase causing a loss of compression and a loss of power. The piston ring can become damaged by a lack of oil which can cause the ring to score the side of the cyl...

This piston assembly replaces worn internal engine components to restore proper compression and combustion. It includes the piston, rings, and connecting hardware needed for engine repair or rebuild work. Replacing a damaged piston assembly helps improve starting, restore power, and ensure smooth, reliable engine operation.

This governor control lever is used on small engines to regulate engine speed by adjusting the throttle in response to load changes. It helps prevent overspeeding while maintaining smooth, consistent operation. This is a direct replacement for worn or damaged levers to restore proper speed control and reliable engine performance.