Craftsman Engine Engines

This is a genuine Toro replacement part. The camshaft is designed by the manufacturer for use in lawn tractors and engines. This part is made of metal, and is placed in the crankcase assembly to interact with the crankshaft. It comes with two metal tappet valves. You may require a wrench when replacing this item. This part is sold individually.

This is an Genuine OEM replacement part used on a variety of Lawn and Garden Engines. This part is made out of Metal and it is sold individually. The Push Rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent pushrod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately.

This spark plug boot is a genuine OEM Briggs & Stratton replacement designed to fit securely over the spark plug, protecting the connection from moisture, dirt, and debris. Its durable, elbow-style design helps ensure reliable ignition and easy installation, making it an ideal replacement when a cracked, loose, or worn boot causes hard starting, misfires, or inconsistent engine performance.

This is a genuine manufacturer-approved replacement part which is specially designed for use on Briggs and Stratton engines commonly installed on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of imme...

This gear-governor is a special component that helps to engage the drive shaft. It is a genuine Briggs and Stratton item that is supplied by the original manufacturer for use with small engines that are commonly installed on a variety of lawn and garden equipment. It provides an identical replacement for a damaged or a missing hardware that was installed on a new unit. Check the diagrams for your ...

This rocker arm adjuster, or valve lash adjuster, is a genuine OEM replacement part used in lawn tractors. It is approximately one inch long and made of steel. It is responsible for adjusting the clearance between the rocker arm and valve stem, which allows the valves to open and close as needed. The adjuster will need to be replaced if the threads are stripped, or if it is cracked, or worn down. ...

This is a manufacturer approved replacement part used on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent push rod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately. This part is made out of metal and it is sold individually.

This replacement 115V line cord is sourced directly from the original equipment manufacturer for use with Ridgid drain cleaning machines. It is hardwired to the tool in order to supply electricity from a standard U.S. outlet, if the cord is damaged it is important to replace it before continuing to use the equipment. This high-quality rubber insulated power cord is sold individually.

This is available as a set of four rings. They are authentic OEM sourced items which are specifically produced for use with Briggs & Stratton engines. The rings are part of the piston assembly and are made out of durable materials. If these parts become broken they will need to be replaced and may require a set of pliers during the installation.

This is sold as a set that contains three rings. The rings attach to the piston and help to create a seal. When replacing these parts a screwdriver, a set of pliers, and a socket set might all be required during the installation process. These parts are made out of metal and will need to be replaced if they break or bend. They are authentic Briggs & Stratton and Toro replacement parts that are sou...

This is an authentic OEM sourced replacement piston ring set which is specially produced for Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of these parts is to provide a tight seal between the piston and the cylinder walls. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase, this would cause low compression...

This crankshaft converts reciprocating motion into rotational power within the engine. Manufactured for strength and balance, it supports smooth operation and reliable power transfer.

This standard-size piston ring set is designed for small 4-cycle engines to help maintain proper compression and efficient engine operation. By sealing the gap between the piston and cylinder wall, it supports smooth starting, consistent power, and reduced oil consumption. It’s a practical replacement option for restoring performance when rebuilding or servicing worn lawn and garden equipment engines.

This is a genuine replacement part manufactured for use with small engines. The breather assembly is commonly used to release combustion gasses that can become trapped in the crankcase. This breather assembly includes the breather gasket, please note the breather tube is available separately.

The cylinder head attaches to the cylinder head gasket. It is an authentic replacement part directly sourced from the manufacturer for use in Briggs & Stratton engines and Toro lawn mowers. This item is available individually. A wrench might be needed during the installation process. This part may become broken and will need to be replaced.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with small engines from Briggs & Stratton and Toro. The metal pin is used to connect the connecting rod to the piston assembly. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

This is an OEM part sourced directly from the manufacturer. The ring set is commonly found in snow throwers from Toro and engines from Husqvarna. This is a set of two metal rings which are inserted into grooves on the outer surface of the piston to help seal it inside the cylinder. You may require pliers and a screwdriver when replacing this item.

This is an authentic OEM part for use with Craftsman Lawn Mowers. The engine breather vents air from the engine crankcase. The most common reason for replacing the breather is when the small engine runs poorly. This part is sold individually. Here is a list of tools that are needed to replace the breather a flat-head screwdriver, hammer, 7/16th-inch socket, 3/8th-inch socket or nut driver, Phillip...