This replacement LED light ring assembly is specially designed for use with Dewalt impact drivers. The worklights are made for lighting the immediate work surface and are not intended to be used as a flashlight. The worklights are activated when the trigger switch is depressed, and will automatically turn off 20 seconds after the trigger switch is released. If the trigger switch remains depressed, the worklights will remain on. Please note this assembly is sold individually.
Removed screws from the body...opened the shell...only thing I didn\'t know was the ring turns and clicked in....but a service repair man told me it snaps off with a flathead screwdriver.....he was wrong ....Otherwise everything went smoothly
1. Remove all screws from the body of the driver
2. Remove one side cover from the driver.
3. Remove motor/ transmission an brush assembly as one unit. Note alignment of electric motor parts.
4. Unplug remove old brush assembly and reinstall new brush assembly.
4a. If ou are replacing the light ring, now is the tim
... Read moree to unplug and remove and replace it.
5. Put brush assembly, motor and transmission together and put back into body of driver.
6.Put other side of driver on and reinstall screws.
Put battery in and test the fix.
I also ordered a new clamshell kit for the impact driver as well. First, I removed all the screws that hold the clamshell on. They are all accessible from the right side. Next, I lifted the right half of the clamshell off the assembly, leaving all the internals attached to the left side clamshell. Then I removed the light ring assembly
... Read moreby first unhooking the power plug connector then turning the light ring clockwise until it would clear the left side clamshell and finally, slid it off the front of the assembly.
The install went like this, I laid the new left side next to the old on full of internals. I lifted the motor bushing assembly up and out before i lifted the power supply/trigger assembly out and moved the whole mess over to the new clamshell and put it back in the same order that I removed it in.
I slid the light ring assembly back in place, rotated it counterclockwise to seat it, and re connected the power coupling.
Lastly, I put the right-side clamshell in place and replaced all the screws.
Easy-peasy, lemon squeezy!
I forget if there were 8 or so Philips screws or if they were small Torx screws, but after removing them and cutting a slit in the warning label the unit splits in half (make sure the battery is already out). Unplug the old LED ring and give it a slight twist (clockwise while looking down onit). It pops right off. Reverse for reassembly.
... Read more Only takes 15-20 minutes if you\'re doing it for the first time.
Read less
Did you find this story helpful?
Thank you for voting!
Rubber protective grip was falling off of the unit.
Actually sent it to Dewalt to be repaired. The gave me an estimate of $89. I can get a new one for around $110. When I received my Impact Driver back from Dewalt it was in pieces in a bag. I found the clam shell and the LED light ring that go on the front for less that $30 shipped to my house. All I had to do was wipe all the parts down
... Read moreand install them into the new clam shell. Took less than 15 minutes.
Take all the housing screws out and separate the housing then you have access to the ring with the lights in it, unplug the power wire and remove the ring, replace the new ring and plug up, now put your housing back together, and WAH LAH you have lights again.
THANKS EREPLACEMENTPARTS
DeWalt 20v impact driver
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of N073422 DeWALT Light Ring Assembly")
_WW_1.gif "Part Location Diagram of N073422 DeWALT Light Ring Assembly")
