Genuine manufacturer sourced replacement switch used on Dremel rotary tool. It is an important part of the tool which handles on/off operations. Because switches have mechanical parts, they will tend to wear out over time, eventually requiring replacement. Switch has a plastic body and it is sold individually. To replace this switch you would need a Screwdriver. • Remove screws used to hold two pieces of housing set together • Disconnect wires from the old switch and remove it from the housing • Place the new switch in the housing and connect wires to it • Reassemble the housing
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Exact replacement
An exact replacement that worked fine. Easy order, prompt shipment, what's not to like with EReplacement parts?
Guest - July 1, 2019
Verified Purchase
★★★★★
★★★★★
Part was perfect fit.
This part came well packaged without any damage at all. The connection terminals were not bent and the part performed perfectly.
Guest - July 2, 2019
Verified Purchase
★★★★★
★★★★★
New
Arrived on time and works great!
Guest - July 3, 2019
Verified Purchase
★★★★★
★★★★★
New Switch!!!
Barely used Dremel 3000 quit working. Purchased this switch and the quality is so much better than the original switch. Dremel works just fine once again!
Guest - April 25, 2019
Verified Purchase
★★★★★
★★★★★
switch assembly
it is the part that fit perfect, received in good condition
Guest - August 20, 2019
Verified Purchase
★★★★★
★★★★★
Switch Repair
I got the right part and it was it installed nicely and works well.
Guest - August 27, 2019
Verified Purchase
★★★★★
★★★★★
Small but mighty!
It came brand new. It was last part needed to make Dremel 3000 new again. Worked perfectly.
Guest - January 14, 2022
Verified Purchase
★★★★★
★★★★★
It was a complex repair, required several parts to my little Dremel tool. Worked great! =)
All of the parts were well packaged & protected. Your system of finding the parts you want is very good. I have a lot of rather old tools; I generally go to you guys first rather than the manufacturer. Keep up that great work! =) Charlie
Charlie - December 2, 2022
Verified Purchase
★★★★★
★★★★★
Easy repair
The part was spot on and with the installation instructions was very easy the only complaint is the price and the cost of delivery almost as much as the price of the part
Tomas - February 1, 2022
Verified Purchase
★★★★★
★★★★★
simple replacements!
R&Rd switch assembly and field coil. Back to work!
Thanks
Guest - May 4, 2019
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Remove the 4 torx screws. Peel labels back, or cut along seam. Remove brushes.
Once removed, separate casing. Remove armature. Remove power wire from switch with paper clip unfolded. Pull switch from armature housing.
Replace switch, push power wires into slots.
Reassemble.
Remove screws from the housing, remove on half of the housing, Note where the cord wires are located. Remove the brush caps and brushes. Remove the defective switch. Replace with new switch. Replace cord leads and insert new brushes and replace brush caps. Assemble housings with the screws. And your done.
Removed the side labels from the Dremel tool body, removed the 4 Torx screws and eased apart the halves. The \'switch\' is actually a circuit board with slider switch, and it unplugged from the armature and the new one plugged right back in easily. Reassembled, plugged it in, works like brand-new gain. Even the Dremel body labels went bac
... Read morek on easily.
Read less
Did you find this story helpful?
Thank you for voting!
Variable speed switch would only work in slow 1 & 2.
Remove the 4 Torx screws, carefully remove one half of the case, best to remove the half without the lock button, use a small pin to remove the power wires from the switch assembly (make sure it is not still plugged in) unplug the old switch assembly and plug the new in, connect power wires then gently put every thing into the recesses i
... Read moren the cases and put the 4 screws back in. Take apart again, look around on the floor for the lock button, install it and put things back together again. Always helps to vacuum the floor before a job like this. It makes it easier to find the dropped parts. It is very satisfying to plug something in that you have repaired yourself and have it work.
1. Removed 4 Torx screws.
2. Removed both brushes.
3. Separated the housing (decals must be sliced along the seam).
4. Removed the armature.
5. Separated the speed control from the armature (easily pulls apart).
6. Removed the wires to the controls switch using a small nail to reduce the spring tension(small
... Read morehole beside each wire).
7. Reinstall the wires in the same location in the new switch.
8. Reattach the control to the armature.
9. Reassembly in the reverse order.
Replaced the switch with On-Off Switch (2610912826). the new switch actually improved the Dremel by providing two speed operation. Originally, the dremel #275 type-4 was a single speed tool.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10259985
Manufacturer Part Number: 2610013852
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
