It is a genuine item that is supplied directly from the original equipment manufacturer for use with Powermate generators. This is an identical replacement for a faulty, a damaged or a missing bridge diode that was installed on a new unit. Note, this high-quality component is sold individually. A screwdriver will be needed to perform this repair. Make sure to refer to the owner's manual and the appropriate diagrams for your model to ensure the correct replacement procedure.
Troubleshooting
This part works with the following brands:
Powermate
This part works with the following products:
Generator
Part# 0048677SRV replaces these:
0048677SRV,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(1 Review)
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Coleman Generator, Np Voltage
Got the Bridge Diode in very quick time. Ordering was very quick and easy. You didn't have the capacitor but I ordered the diode. Installed it and generator still had no voltage. I then saw the capacitor had a bulge in it. Since you didn't have the capacitor I ordered one from E-bay and received it in 2 days. Installed it and plugged an electric light into the generator and pulled the rope and Whammo ! I had light. Thank you for providing parts for the consumers. Would I order from you again ? Definitely yes, you are a good company to order from.
Guest - July 6, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Completely remove generator multi voltage receptacle panel.
2 Remove the four 14 gauge wires from Bridge Diode.
3 Remove Bridge Diode hold down nut and remove old Bridge Diode.
4 Install new Bridge Diode and reverse removal procedure.
5 Check all other wire connection before reinstalling panel.
6 Star
... Read moret up generator and check voltage output from all receptacles.
7 Test all good.
Read less
Did you find this story helpful?
Thank you for voting!
generator AC output was down to approximately 10 watts.
I removed the old brushes and checked for wear. They were seriously worn down. I could get nothing when checking the bridge diode for voltage resistance when checking matching wires. The rotor tested good output when I tested both copper sides. I replaced the brushes and bridge diode with new components from eReplacementParts.com. Wh
... Read moreen the generator face was replaced, I started it and checked the output. It was operating perfectly. This was on an old Coleman Powermate, model OHM110-222712c 6875/5500 watt generator with an 11 hp Tecumseh engine that I had purchased in about 2003 and has seen a lot of use. It appears as though I will be getting more use out of it in the future.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
