This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Great fit! Super price
Back in service, great supplier to do business with
David - June 15, 2019
Verified Purchase
★★★★★
★★★★★
Easy to find
This was a recommended item to the item I was looking for. Thank you.
Guest - July 29, 2019
Verified Purchase
★★★★★
★★★★★
Replacement part for fuel tank
I needed 3 of these along with a new fuel tank for my trimmer. All the parts fit exactly, even on my older model trimmer. I’ll come back to this site if I need more parts in the future. Good transaction all around.
Wayne - August 21, 2019
Verified Purchase
★★★★★
★★★★★
Needed part.
Part was missing easy to install.
Guest - October 4, 2019
Verified Purchase
★★★★★
★★★★★
Perfect fit after all these years.
Received parts in new condition. Last time my blower had new bumper SC was in the early 90s when I bought it!
Guest - October 11, 2019
Verified Purchase
★★★★★
★★★★★
All parts were perfect.
The parts all fit perfectly, were priced competitively and working great!
Guest - September 19, 2023
Verified Purchase
★★★★★
★★★★★
Easy repair.
Very simple repair.
Guest - May 3, 2025
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Removed all fuel.
2. Removed all parts to be replaced, as well as trim and parts that needed to be removed in order to install new parts, including the spark plug, air filter and air filter holder, carburetor, old fuel tank and fuel lines, and fuel tank bumpers.
3. Installed new spark plug after setting proper gap.
4.
... Read more Installed new fuel tank and lines, and bumpers, having noted where the new lines would go when I took the old tank off.
5. Disassembled the carburetor (simply removed 4 screws around the primer bulb to do this) and replaced the tiny fuel filter screen inside, then reassembled it. (Note-the small needle was used to remove the old fuel filter screen.)
6. Replaced carburetor on its two mounting posts.
7. Replaced the air filter holder, with new filter installed inside of it in its place on top of the carburetor.
8. Checked all nuts and screws for snug fit.
9. Added new-fresh fuel.
10. The device fired-up and ran well on the second pull of the starter cord, after proper priming per manufacturer\'s instructions.
Remove the tank by removing the screws holding it and remove the fuel lines
Place the new bumpers on the new tank and install the new tank on the trimmer
Connect the fuel lines
1. Drained fuel tank.
2. Removed screws from blower shroud.
3. Removed screws from crankcase cover.
4. Placed rag into crankcase opening to eliminate debris falling into the motor.
5. Removed old crankcase gasket and removed gasket reside with a sharpened putty knife.
6. Disconnected existing fuel lines and r
... Read moreemoved old fuel tank.
7. Attached new fuel lines and installed new rubber bumpers.
8. Seated new fuel tank.
9. Installed new crankcase gasket and removed rag from Step 4.
10. Reattached crankcase cover.
11. Reattached blower shroud.
Read less
Did you find this story helpful?
Thank you for voting!
No start-had not run for 15 years-had been left with gas and oil in the machine-never properly stored
Replaced primer bulb and cleaned carb with aerosol spray, replaced fuel tank (old one was cracked), Put in fresh gas/oil mix but still would not start. I bought a new spark plug and then it ran. Adjusted carb and it now works great. Including the carb kit I have $32 invested and it runs like a new machine again and starts easily.
Did you find this story helpful?
Thank you for voting!
Trimmer gas tank bumpers missing or never installed at factory
Leaf Blower / Vacuum
- Homelite Leaf Blower Model BX90 Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of 98792 Homelite Grommet")
_WW_1.gif "Part Location Diagram of 98792 Homelite Grommet")
