Part Location Diagram of H-303202001 Hoover Brush Roll Assembly
See part 21 in the diagram
( Grid squares measure 1x1 inch )

Brush Roll Assembly H-303202001

Manufactured by:
Hoover
ERP Number:
ERP12065477
Part Number:
H-303202001
Original Equipment Manufacturer ?
Special Order

Easy 

Less than 15 mins 

(5 rated repairs) ?

Does this part fit my model?

Need help finding your model number?

Product Description

?

This authentic manufacturer approved replacement brush roll assembly is designed for use with Hoover vacuums. The spinning motion of the brush rolls picks up the dust and dirt from the floor. Over time bristles will wear out and would need to be replaced. It is made out of plastic and it is sold individually. When replacing this part you would need a screwdriver. • Remove nozzle plate • Remove old brush roller and snap the new one into place • Secure the access plate

Troubleshooting

This part works with the following brands:
  • Hoover
This part works with the following products:
  • Upright Vacuum

Customer Part Reviews

?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
  • 5 stars
    4
  • 4 stars
    0
  • 3 stars
    0
  • 2 stars
    0
  • 1 star
    0
  • 1
Sort by:  
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

Less than 15 mins 

(5 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Bent brush roller

Dennis from LAKELAND, Florida

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
H-303202001
Removed the bottom of the vac.
Removed the old brush roll
Put the belt around the new brush roll and inserted it into the vacuum
Replaced the bottom
Did you find this story helpful?
Thank you for voting!

Original belt and spool were worn and slipping

Norman from Deming, New Mexico

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
H-AH20080, H-303202001
Laid vacuum on back side.
Turned and slid 2 retainer clips and removed a few of the phillips screws to gain access to belt and spool ends.
I pushed belt off shaft, lifted out spool assembly.
Placed new belt on spool, engaged belt on motor shaft, then forced the two square ends of spool into their slots.
Replace d screws, slid and turned two retainer clips to lock assembly in.
Done.
Did you find this story helpful?
Thank you for voting!

Brush was worn down. Figured a new one would pick up better.

William from Reno, Nevada

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Parts Used:
H-303202001
Read the instruction book that came with the vacuum from step 1 thru step 4. This was a very simple job.
Did you find this story helpful?
Thank you for voting!

Brush Roller broke at the axle

Jeremiah from New Richmond, Wisconsin

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Parts Used:
H-303202001, H-303172001
Just needed to take the old one out and swap in the new one. Really simple.
Did you find this story helpful?
Thank you for voting!

was not picking up from carpet

Robert from Lakewood, Washington

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Parts Used:
H-562289001, H-303202001
Removed the old parts, replaced with new parts. So easy my wife did it,
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP12065477
Manufacturer Part Number: H-303202001
Brand Model Number Description
Hoover CH53005 Upright Vacuum - Task Vac Hard Bag Lightweight
Hoover CH53010 Upright Vacuum - Task Vac Bagless
Hoover UH30300 Upright Vacuum - WindTunnel Bagged Upright
Hoover UH30302 Upright Vacuum - WindTunnel T Series
Hoover UH30308 Upright Vacuum - WindTunnel T Series
Hoover UH30310 Upright Vacuum - WindTunnel Pet Bagged Upright Vacuum
Hoover UH70100 Upright Vacuum - WindTunnel Purely Pet
Hoover UH70100RM Upright Vacuum - WindTunnel Bagless Upright T-Series
Hoover UH70105 Upright Vacuum - WindTunnel Purely Pet
Hoover UH70106 Upright Vacuum - WindTunnel Purely Pet
Hoover UH70110 Upright Vacuum - WindTunnel Series Rewind
Hoover UH70115 Upright Vacuum - WindTunnel Series
Hoover UH70116 Upright Vacuum - WindTunnel Series
Hoover UH70120 Upright Vacuum - WindTunnel Series Rewind Vacuum
Hoover UH70130 Upright Vacuum - WindTunnel Series Rewind Vacuum
Hoover UH70140 Upright Vacuum - WindTunnel Rewind Plus Bagless Upright
Hoover UH70200 Upright Vacuum - WindTunnel Series Vacuum
Hoover UH70202 Upright Vacuum - WindTunnel Upright Vacuum
Hoover UH70205 Upright Vacuum - WindTunnel Series Vacuum
Hoover UH70210 Upright Vacuum - WindTunnel Series Vacuum
Hoover UH70211 Upright Vacuum - WindTunnel Series Vacuum
Hoover UH70212 Upright Vacuum - WindTunnel Series Vacuum
Hoover UH70215 Upright Vacuum - WindTunnel Series Vacuum
Hoover UH70240 Upright Vacuum - WindTunnel Rewind Plus
Hoover UH70604 Upright Vacuum - Remedy Multi-Cyclonic Bagless Upright Vacuum