This is a genuine manufacturer sourced replacement part designed for lawn and garden equipment engines. This gasket provides an air-tight seal for the float bowl. Over time this gasket will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of rubber material and it is sold individually. Replacing this item you would need a screwdriver.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
right part!
although gasket and air cleaner were the right parts and fit, and the small round gasket in the float bowl was rotten and the new one was perfect, it was not the only problem. Engine starts and idles albeit somewhat rough, engine wont accelerate stalling out when revving. Which was the main reason for attempting fix it. Back to the drawing board!
Guest - May 7, 2019
Verified Purchase
★★★★★
★★★★★
Exactly what I needed!
I found the part easily at the site and it was exactly what I needed to get my mower running again!
Guest - June 25, 2019
Verified Purchase
★★★★★
★★★★★
Perfect part
Exact fit fast delivery well packaged
Guest - September 7, 2019
Verified Purchase
★★★★★
★★★★★
perfect fit
My log splitter is back online, enough said
Michael - November 25, 2019
Verified Purchase
★★★★★
★★★★★
Always get the right part.
Brand new factory part. Quick shipping. Far price.
Guest - May 15, 2021
Verified Purchase
★★★★★
★★★★★
Repair
Perfect fit.
Guest - July 17, 2021
Verified Purchase
★★★★★
★★★★★
great service
Great service and fast delivery!
Anonymous - June 2, 2022
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
The main jet and feed tube had gunk that needed cleaned out. The real issue was the solenoid at the bottom of the bowl. Debris was in it, and would not allow it to fully retract, partially blocking fuel flow to the main jet. I am going to need a new fuel solenoid, but these gaskets sealed everything up nicely.
I just replaced the parts i ordered on the carb. All parts fit as intended. However, the engine will start and run but quickly starts sputtering/missing. I also replaced the spark plug. Not sure what else is wrong but I think I can get the yard mowed with it. Just not running right.
Did you find this story helpful?
Thank you for voting!
carburetor flooding over and drained fuel tank into the crankcase.
Jeff from ALTA, Iowa
0 of 1 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
removed carb, cleaned, and rebuilt it with the new parts. installed on engine. Drained crankcase that had oil / gas mix. refilled oil and changed filter. started up and runs good.
Did you find this story helpful?
Thank you for voting!
I have a Murray 42\" lawn tractor with a Briggs and Stratton engine. It is 17 years old and the only work I had done on it was on the cutting deck. After this winter I could not get it to start. The e
1. I have a Murray 42\" lawn tractor with a Briggs and Stratton engine. It is 17 years old and the only work I had done on it was on the cutting deck. After this winter I could not get it to start.
2. The engine would crank but not start. I put new gas in and checked the filter. I checked the spark plug and they were good.
3
... Read more. I pulled the carburetor and cleaned the bowl, but the gasket was soft and brittle.
4. The engine would start bu once I pushed the throttle it would shutdown and not start back.
3.I decided I had to get into the carburetor. I bought the bowl gasket and the check valve. I pulled the carburetor down and cleaned it out. There was sludge in the bowl and jet. I rebuilt it with he new parts and the engine started in the first start.
Remove the screw from the bottom of the float bowl and the gasket. Remove bowl and clean the inside of it. Removed the old gasket and installed the new one. Then reattached the bowl to the carburetor with the screw.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9066958
Manufacturer Part Number: 698781
Engine
- Briggs & Stratton Small Engine Model 19H237/0125-H1 (19H237/0125H1, 19H237/0125 H1) Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Seal or Gasket","title":"Seal or Gasket","url":"/parts/lawn-and-garden/engine/seals-and-gaskets/"},{"position":2,"name":"698781","title":"698781","url":""}]
