This replacement gasket is supplied directly from original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is used to provide an air-tight seal for the crankcase. Over time gaskets tend to get compressed and crack eventually requiring replacement to maintain peak performance. This part is made of high-quality composite material and it is sold individually.
Removed engine from tractor
Watched a few YouTube videos on how to dismantle engine
Unbolted sump pan and pulled apart carefully
Cleaned gasket material off with scraper and sandpaper
Used gasket sealer with gasket to replace old gasket
Reassembled and torqued to 225 inch lbs the bolts in a cross pattern
... Read more/>
Gotchas: Be careful of the governor assembly
Oil seal is a challenge to remove
During reassembly turn the crank to line up the governor gear to the cam sprocket
Be sure the timing marks line up between crank and cam gears
I disconnected the battery,starter,removed crank drive pulley,remover motor bolts that hold it to the frame. One the motor was free, I drained the oil,removed the motor from the frame, and turned it upside down on wood framed roll around. Then removed the crankcase, cleaned and removed the old gasket and used a seal remover tool to rem
... Read moreove the crank seal. I installed a new seal turned the case bottom side down installed the governor and snapped it into place. I cleaned the block to remove the rest of the gasket. I then installed the new crank gasket, turned the crank case over and slid it over the oiled crank down to the cam gear and lined up the governor gear and cam gear and the case slipped into place. I installed the 7 bolts and tightened them down in sequence and torque to spec, turned the motor back over installed on the frame of my garden tractor. Reinstalled the 4 bolts that holds the motor in, replaced the main pulley, connected the starter, connected the choke, throttle cables, filled the crankcase with oil, connected the battery and started the motor and let kit run for a while and checked for leaks and there were none. Mower is ready to go back to work.
I removed the engine from the lawn tractor, split the crankcase, cleaned old gasket, and installed new sump gasket. I replaced the old oil seal, (pto side) and reinstalled engine. No more oil leaks. Thanks guys.
Did you find this story helpful?
Thank you for voting!
Oil leak under machine
frank from fort collins, Colorado
1 personfound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Remove the mower deck, remove drive pulleys,remove the engine. Separate the crankshaft, clean the block and crankshaft mating surfaces, apply the gasket, reverse to reassemble
Did you find this story helpful?
Thank you for voting!
The engine was leaking oil. The fuel filter needed replaced anyway, but broke when removing.
Take crank covers off, clean parts, use engine assembly lube when putting movable parts back together, torque bolts down to specifications. The fuel filter is between two hose clamps. Slide the clamps back, take out the old fuel filter and replace. If the hose clamps are weak, replace.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9064881
Manufacturer Part Number: 692292
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Seal or Gasket","title":"Seal or Gasket","url":"/parts/lawn-and-garden/engine/seals-and-gaskets/"},{"position":2,"name":"692292","title":"692292","url":""}]
(1989)_WW_3.gif "Part Location Diagram of 692292 Briggs and Stratton Gasket-crankcase")
(1989)_WW_3.gif "Part Location Diagram of 692292 Briggs and Stratton Gasket-crankcase")
