This starter clutch is an authentic OEM replacement part used in small outdoor power engines. Each package includes one clutch and one ball bearing. The starter clutch allows the engine to start by engaging the crankshaft to spin the engine and initiate combustion. Once the engine starts the clutch disengages to prevent over spinning. Over time the clutch may fail due to worn-down bearings, or damage to the clutch body, resulting in hard starting or failure to start. To replace it, first, disconnect the spark plug for safety. Then, remove the engine cover to access the starter clutch. Remove the clutch from the crankshaft, and thoroughly clean the mounting shaft. Install the new clutch by screwing it onto the crankshaft, then reassemble the engine cover and reconnect the spark plug.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Good
Works great. Put it on an old 8hp Briggs for Troybuilt tiller
Guest - October 11, 2019
Verified Purchase
★★★★★
★★★★★
Easy fix
Part arrived in 3 days installed In under 2 minutes and my generator now works and sounds like new. I will be using site again for my part needs.
Guest - December 12, 2019
Verified Purchase
★★★★★
★★★★★
Easy to install worked great
This item took awhile to recieve, had to cancel other items that were on backorder
Rick - May 6, 2020
Verified Purchase
★★★★★
★★★★★
Part worked great perfect
Poooo
Guest - June 8, 2020
Verified Purchase
★★★★★
★★★★★
Easy & quick repair!
This matched up perfectly with my 1992-93 era Poulan/weedeater rototiller, 5hp Briggs & Stratton. Running great again.
Guest - March 31, 2021
Verified Purchase
★★★★★
★★★★★
Excellent customer service
Will definitely check back with you first should I need more parts.
Guest - December 31, 2021
Verified Purchase
★★★★★
★★★★★
Just what I needed
After several failed attempts to lubricate the old one, I replaced it. Works like new.
Guest - October 8, 2022
Verified Purchase
★★★★★
★★★★★
repair
The shipping took longer than what it stated when I made the order it said ship in one day I got the part in a week and it was not in the box when I received it.
Guest - August 12, 2019
Verified Purchase
★★★★★
★★★★★
Very old roto tiller
It’s great to find a parts store that has the part You need . Very old machine , now runs like new. Will be returning , to get more items thank you
Guest - May 18, 2022
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Removed starter housing from engine by removing 3 one quarter inch bolts.
2. Removed recoil starter spring to reshape end to fit into plastic rope pulley.
3. With assistance, rewound starter spring into housing and reattached new rope pulley.
4. Wound starter spring and installed new starter rope.
5. Using a spe
... Read morecial tool, removed starter clutch using an electric impact gun.
6. Using the same special tool and impact gun, installed new starter clutch.
7. Reattached complete starter housing to engine with the three bolts.
8. Started engine to insure everything operated normally.
Read less
Did you find this story helpful?
Thank you for voting!
starter clutch was slipping and rewind spring was not pulling starter cord back in
removing of the pull starter mechanism
replacing of the old starter clutch
replacing of the rewind starter spring and replacing pulley
spring is difficult since starter cord needs threaded into the pulley while holding the coil spring
small stiff wire helps with pushing cord into pulley
pulled cover, replaced all parts needed. you have to make sure you wind up the starter spring enough so when you let the rope retract it returns all the way in. and if you pull the seal off the starter clutch, old part. watch out for ball bearings to drop. I couldn\'t believe that parts were still available for my 42 year old pincor gener
... Read moreator. I almost junked it, now it\'s back in service running great. thanks for being there.
1. Removed cover and mesh.
2. Removed old clutch and washer.
3. Used scouring pad to clean shaft.
4. Installed new washer and clutch.
5. Replaced mesh and cover.
Did you find this story helpful?
Thank you for voting!
bearings in old clutch failed - starter rope will not retract
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
