This genuine OEM part is manufactured by Milwaukee. It is compatible with a variety of their handheld power tools. This one (1) piece set includes plug, cord, and cord protector. A cord protector prevents damage to the cord by reducing strain put on the point of connection between wires and machine. Replace this set when any component is damaged.
Troubleshooting
This part works with the following brands:
Milwaukee
This part works with the following products:
Electric Drill
Reciprocating Saw
Demolition Hammer
Hammer Drill
Cordless Drill
Charger
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Great for older Hole Hawg
I had to cut the ends with the connector pins off the old cord and reuse them but the cord was good quality and the molded strain relief fit perfectly.
Larry - September 9, 2020
Verified Purchase
★★★★★
★★★★★
Great factory part
Cord was excellent easy to install. I was operational in less than 10 minutes
Guest - June 1, 2021
Verified Purchase
★★★★★
★★★★★
Easy Transaction
Easy to find, fast shipping, a very smooth transaction.
Guest - July 30, 2021
Verified Purchase
★★★★★
★★★★★
OEM Replacement power cord for 1/2" Milwaukee Drill
Always appreciate eReplacementParts quick service and stocking many OEM parts. Only thing that would have made it perfect was if three electrical butt splices would have been completed - but inexpensive and easy to obtain. Thanks for great products.
Milton - September 16, 2022
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Remove handle cover, then remove cord clamp. You then remove the old cord wires from the switch and ground wire and discard old cord. Attach the new cord wires to the switch and attach the ground wire, Reattach the cord clamp, tuck the wires out of the way so the won\'t get pinched, then screw the handle cover back on.
Installed new cord set on drill motor after installing terminals on wires. Very simple, wires are color coded and cord protector fit perfectly in the drill motor handle.
Basically easy but was disappointed that the replacement cord lacked the connectors. They re not standard so I had to remove them from the old cord (a PITA) and attach them o the new cord.
Removed screws in handle to get access to inside to replace the cord.
Replaced cord and put handle back together and tighten the screws.
1/2\" drill is 50 plus years old..... original cord....
There is nothing special about replacing the power cord.
Removed one half of the switch handle
Removed the switch from the handle
Made a wiring diagram, check for continuity, new switches wire differently.
Remove the ground wire and the switch and old cord
Install the wires into the switch
Install the ground wire
Screw the switch into the handle
Attach
... Read morethe handle to the drill
Separate handle halves....Remove old cord...Cut off wire connectors...Install new cord in notches of handle.....Reconnect two wire with new wire connectors(not provided) to drill motor....Reattach handle halves.... Plug in test drill
Did you find this story helpful?
Thank you for voting!
The protective cover of the power cord on my Milwaukee Sawzall had disintegrated.
Removed one side of the plastic casing, about 5 screws
Cut the power and ground wire to free from saw motor
Positioned the new power cord and soldered the new leads to the appropriate lug
Replaced the side casing and secured with screws.
Took the handle apart
Removed the cord wires from the switch and the ground wire
Connected the new cord wires to the switch along with connecting the ground wire
Made sure all of the parts were where they belong , then put the handle together
Removed both carbon brushes, about 8 screws to remove one side of handle cut old cord wires. Replaced cord set 18-36 w/protector.
Great service from eReplacementParts.com
Lee M.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of 22-64-0405 Milwaukee Cord Set")
_WW_1.gif "Part Location Diagram of 22-64-0405 Milwaukee Cord Set")
