This edge guide is an OEM direct from DeWALT. The metal component is designed for use with lawn edger devices. The edge guide is fastened to the blade guard, allowing the operator to safely make accurate lawn edging. A screwdriver, socket set and a pair of pliers may be required for the installation. The edge guide is sold individually.
Troubleshooting
This part works with the following brands:
Black and Decker
Craftsman
This part works with the following products:
Edger
Trimmer
Part# 244276-00 replaces these:
244276-00, P244276-00,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(9 Reviews)
Click to filter by ratings:
5 stars
9
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Arrived On-Time
The part appears to be correct for my edger but I have not installed it. The original part is still serviceable. I purchased this one as back-up when the original one no longer functions satisfactorily.
Spencer - July 8, 2019
Verified Purchase
★★★★★
★★★★★
Hard to Find!
I've been looking for this part for a while. Glad to find it even at a reasonable price!
Randy - July 21, 2019
Verified Purchase
★★★★★
★★★★★
Satisfied
This was the part I needed. An easy search and fast delivery.
William J - May 18, 2020
Verified Purchase
★★★★★
★★★★★
Easy repair, great service and quality
the blade was wore down really bad. Ordered a replacement. It is just like new. Edging is smooth and easy again
Guest - June 30, 2020
Verified Purchase
★★★★★
★★★★★
Reasonably priced parts
Our part was shipped immediately and made a huge difference when we installed it on our edger. Thank you!
Guest - October 5, 2020
Verified Purchase
★★★★★
★★★★★
Fast and great price
I was impressed with which the speed that I received the product and was very impressed with the low price as well. I will look to them again in the future when I need parts.
Guest - June 12, 2021
Verified Purchase
★★★★★
★★★★★
Edger guide replacement
Like new part- easy to reinstall and get edging the lawn again. Quick delivery, too!
Guest - October 12, 2021
Verified Purchase
★★★★★
★★★★★
Black and Decker Electric lawn edger and trencher
The parts were exactly as the originals(I ordered two). The person on the phone was knowledgeable and the shipping was fast. Definitely a good source for part.
Guest - August 14, 2023
Verified Purchase
★★★★★
★★★★★
Great service
Great service
Guest - June 4, 2024
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Locked old blade in place with screw driver placed in hole in blade. Used socket set to remove nut holding blade on. Removed blade. Removed c clip with screw driver that holds edge guide in place. Removed edge guide. Put on new edge guide. Struggled to replace c clip back. Put on washer then new blade then another washer. Screwed on nut.
... Read morePut screw driver in hole in new blade to stop it from moving and tightened it good.
Read less
Did you find this story helpful?
Thank you for voting!
Rear bearing in the motor failed causing a lot of racket and poor performance
Disassembled the housing and removed the motor housing. Tapped the old bearing off of the motor shaft. I then replaced the brush holders with new as a maintenance item. I then replaced the blade and edge guide during the rest of the reassembly process. It all went well and since I cleaned everything up as I went, the edger now looks and r
... Read moreuns as good as new. The whole process was facilitated by the exploded part view shown on the ereplacement parts website.
1. Removed the blade. Used vice grips to hold blade while using socket set to remove nut holding blade in place.
2. Used snap ring pliers to remove the snap ring holding in the edge guide.
3. Removed the blade housing so I could remove the bolt that holds in the front wheel.
4. Assembled front wheel.
5. Put blade
... Read morehousing back in place.
6. Installed new edge guide.
7. Used snap ring pliers to install snap ring to hold edge guide in place.
8. Put the blade back on. Used vice grips to hold the blade while I tightened the nut holding it in place with socket set.
Took off spring clip for guide and removed part put new one on and replaced clip. Blade took off bolt and washer assembly put new blade on and replaced washers and bolt. That\'s it Have done this many times before.
Did you find this story helpful?
Thank you for voting!
Edge guide and blade just wore out through seasonal use.
-Disconnected unit from electric outlet
-Removed blade holding lock nut & blade
-Removed guide holding expansion ring & guide
-Reassembled unit with replacement parts
Remove hub cap from front wheel, remove bolt from center of wheel , replace new wheel. Removed worn edge guide from blade guard and replaced with new one. Simple repair.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP11925370
Manufacturer Part Number: 244276-00
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
