This is a genuine manufacturer approved replacement part designed for use with air compressors. This is the hose that delivers air from the tank. It is made out of rubber and it is sold individually. Please note the hose clamps are sold separately.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Porter Cable pancake compressor
Ordered a air hose and clamps Repair went fine and compressor is working again!
Guest - October 30, 2020
Verified Purchase
★★★★★
★★★★★
Great place for parts
Always have the parts I need and with fast shipping my down time is minimal.
Cliff - January 18, 2021
Verified Purchase
★★★★★
★★★★★
Worked as advertised
The part was an exact fit. I received the part a few days after I placed the order.
Guest - September 27, 2021
Verified Purchase
★★★★★
★★★★★
Quality service and parts
Replaced tube to porter cable air compressor savings $$$ in replacement. I've used ereplacement in the past as well. Reliable service, price and quality parts.
Guest - December 21, 2022
Verified Purchase
★★★★★
★★★★★
Exactly what I needed
Great product and very fast shipping
Guest - August 11, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
I used a screwdriver to remove two screws holding the motor onto the frame. Then unscrewed four screws to open the motor housing. Then removed the broken hose. Attached the new hose and clamped the hose on each end to secure it. Simple. Just remember to route the motor power cord inside the motor housing along the edge when putting the ho
... Read moreusing back together to avoid the fan from striking the cord. Reverse procedure in reassembling
Remove the compressor housing - see YouTube videos for how to. Remove bad hose clamps by twisting hose clamps with pliers and install new hose and clamps
I followed instructions in ereplacementparts YouTube video. The instructions were excellent, except that the video didn\'t show that 3 different types of screws are used (1 phillips, 2 different star heads) are used to hold everything together. Or that some of the screws for the housing were in a tube that was deeper than the shaft of my
... Read morescrewdriver, necessitating a trip to the hardware store to buy an extension for the driver (and hose clamps for the air hose, which did not ship with any. Advice to others: upon reassembly, make sure the power cord is properly seated in its channel so that it does not get hit by the motor fan!!!
I removed the cover with a Torx screwdriver, the old clamps with pliers and pried off the old hose. Then I slid the clamps on the hose, the hose on the pipes and crimped the hose with the pliers. Reattached the cover and the repair is done.
1.Remove compressor from tank.
2. Unscrew old manifold from tank. Nipple remained in tank.
3. Easy-out removes nipple.
4. Assemble new manifold onto tank.Install compressor and hook up the hoses.
5. New manifold has hose barb in wrong spot, hard to contort the hose to fit.
Did you find this story helpful?
Thank you for voting!
Compressor was leaking air from the exhaust port in the head.
I\'ve never made a repair on a pancake compressor before. I disassemble the housing and tried to determine where the leak was coming from. The design made it particularly difficult to ascertain what had failed. I initially thought the head gasket and maybe the valve plate were the cause. I changed those components and the compressor s
... Read moretill leaked (significantly). It then became obvious the check valve was the culprit. I only noticed the hi pressure hose was worn and needed changing. Upon disassembly I found the check valve rusted inside and out. Once I changed those components and reassembled. The compressor operated as expected. It holds pressure just as I would expect.
1. Disconnected the motor from housing.
2. Disconnected wiring to open up the compressor unit.
3. Removed two hose clamps and replaced two hoses.
4. Reconnect wiring and reassemble compressor housing.
5. Plug in and test.
Needed to open up the housing on the compressor to remove one clamp at the end of the hose.
Removed the other clamp at the other end, removed the hose and did the reverse with the new hose and clamps.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP18992718
Manufacturer Part Number: H-7051
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Hose or Tube","title":"Hose or Tube","url":"/parts/power-tool/compressor/hoses-and-tubes/"},{"position":2,"name":"H-7051","title":"H-7051","url":""}]
