This replacement belt is an authentic OEM sourced item, not an aftermarket imitation. It is commonly used on Campbell Hausfeld air compressors. It is the main belt that drives the unit. Over time rubber belts tend to wear out and stretch requiring replacement. Please note, this item is sold individually. To complete this repair you will need a wrench. • Remove the belt cover • Take out the old belt • Secure the new belt • Reattach the housing
Troubleshooting
This part works with the following brands:
Campbell Hausfeld
This part works with the following products:
Compressor
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(3 Reviews)
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Great
Fit compressor just right
Guest - October 24, 2019
Verified Purchase
★★★★★
★★★★★
Worked great
Just what I ordered, came quick, and fair price
Shelia - May 15, 2020
Verified Purchase
★★★★★
★★★★★
look a photo before ordering, cross reference did not work well
actually the cross reference went to a v-belt, I should have looked a photo, it will work on one of my mowers
Guest - September 12, 2020
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Turned power off to the compressor, put the belt over one pulley and started it on to the other pulley then slipped a screwdriver between belt and pulley and rotated the belt till the screwdriver wedged between pulley and belt. Kept turning until screwdriver released on bottom side of pulley. That\'s it easy as pie
Remove belt guard. And broken belt, loosen the electric motor, install new belt, adjust motor to tighten the belt, tighten the motor down, reinstall the belt guard.
Did you find this story helpful?
Thank you for voting!
Belt was so loose it actually melted as it was turning.
1. Loosened the nuts holding the motor in place.
2. Slid motor to loosen the belt tension.
3. Removed old belt and replaced with new belt.
4. Slid motor back in place to tighten the belt using a pry bar.
5. Tighten nuts.
6. Tested.
Removed the belt guard
Loosened the motor base
Removed the old belt and installed the new belt on the pulleys
Tightened the motor tension on the new belt, and tightened the bolts
Installed the belt guard
1. Loosened 4 bolts that holds the motor in place.
2. Slide electric motor with small pulley towards large pulley.
3. Removed old belt and cleaned pulleys.
4. Installed new belt over pulleys.
5. Slide motor back in place and put some tension on the electric motor to hold the belt tight.
6. Tightened 4 bolts t
... Read morehat holds the motor in place.
7. Turn compressor on, popped a top to celebrate the repair....
Removed the belt guard
Loosened the nuts on the motor base
Removed the old belt
Installed the new belt
Put the correct tension on the new belt by pushing the motor and tightening down the nuts
Installed the belt guard
Rolled out compressor so I could access the back; unscrewed the single screw to remove pulley cover; removed the old belt, it just about fell off; installed the new pulley belt by turning the larger pulley by hand. Was rather simple; reinstalled the cover and moved the pulley back to its location; plugged it back into the electrical outle
... Read moret...DONE!
1. Bled residual air from compressor to disconnect piping and remove guard.
2. Loosened set screw on driven pulley and removed old belt. Pulley was rusted somewhat to the shaft. A little extra effort was required to get it free.
3. Installed new belt. checked alignment and reconnected piping.
4. Installed guard and teste
... Read mored.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10242647
Manufacturer Part Number: BT013001AV
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of BT013001AV Campbell Hausfeld Belt")
_WW_1.gif "Part Location Diagram of BT013001AV Campbell Hausfeld Belt")
