This part comes directly from the manufacturer. This Lever is used in made Oster Pro clippers. This part is made of nylon. The Lever is used to drive the blade back and forth for cutting hair. This part needs to be replaced if the tip becomes worn and the blade becomes noisy during use. This part is commonly purchased with the Brush and Spring Assembly (part number 042584-025-000) and Clipper Grease (076300-105-005).
Troubleshooting
This part works with the following brands:
Oster
This part works with the following products:
Clipper Trimmer
Part# 44946005000 replaces these:
44946005000,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
clipper lever
I received this part for my clipper blade in a short time. It is exactly as pictured. Unfortunately it was not the solution to my problem. Now I have an extra for the future.
Sherry - June 18, 2019
Verified Purchase
★★★★★
★★★★★
GReat product and fit
Ordered this for an old clipper, Fit and function was great
Guest - June 26, 2019
Verified Purchase
★★★★★
★★★★★
Parts for Clippers
Took a while due to back order delays, but eventually got here in good shape. Good communication to keep me advised of status. Thanks.
Guest - December 18, 2020
Verified Purchase
★★★★★
★★★★★
Best Source of Parts I’ve Found
I love doing my own repairs whenever I can. I have had many occasions to use eReplacement Parts for many of my parts needs. It doesn’t seem to matter what I’m working they have the parts and many time when no one else has them available. They are a trusted source I will continue to count on.
David - June 21, 2022
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Easy
15 - 30 mins
(11 rated repairs)?
< Prev
1
2
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Blade assembly would not latch in. (2 speed Oster A5 Turbo clippers) broken spring and loose screws sockets.
First I found that the Latch Assembly screw sockets that hold the latch in place had pulled loose from the clippers aluminum housing. This issue caused the latch from pulling tight against the clipper housing. I wiped the surface clean and took some acetone or (you can use wife\'s finger nail polish remover) on Q-Tips and cleaned the hole
... Read more. I took some Loctite and applied it to the hole and screw sockets and let it hardened well. Okay now, I took less than 10 minutes to install the parts purchased. The Parts worked and Clipper work great.
Note: I would check the screw sockets that hold the Latch Assembly in place (they should be flush with clipper housing). This has happened to me before so it might be happen to you.
Read less
Did you find this story helpful?
Thank you for voting!
Clipper blade appeared to operate, but would bind easily whether dog recently bathed or not.
The Oster A-5 Turbo clipper is a good tool, but when the tip of the lever becomes worn, the blades will not cut wiry dog coat, nor anything else for that matter. Instead of buying a new blade, consider replacing the plastic lever. Remove two top screws, lift out the lever, and replace with new. Do not see need to replace the metal link,
... Read more although the plastic gear does show some wear and will be a future purchase.
Read less
Did you find this story helpful?
Thank you for voting!
The blade assembly was worn and not holding blades securely. The clippers are about 2 yrs olde just need a cleaning a lil overhaul
No special instructions needed for installation.. It\'s nice that ereplacements has a diagram of the model... It could be a bit clearer but it did work.. I\'ve had to use this site 3 or four times it is very useful.. I make money with my clippers it\'s good to be able to repair on my own and get back to business..
As I\'m sitting in the barber chair, I notice the clippers are very noisy. Mention it to my barber who tells me the only fix is replacing the clippers. I disagree and he gives them to me to bring home and check out.
Disassembled clippers
Found motor end bushings worn, gears worn causing noise.
Purchased all bearings, sea
... Read morels, and gears.
Greased/oiled and reassembled, retested, that\'s one happy barber!
Please note, if the motor field does not come out of the housing easily, it will need to be pulled out using a small gear puller or other homemade puller tool.
I removed the cover from the clipper and then removed the old lever. I then replaced it with the new lever and original cover. It was quick and easy, and the clipper works fine now.
Take top cover off by removing 2 screws, remove lever, clean out old grease, re-grease, install washer and lever, replace cover, remove brushes one at a time, replace, apply AC, and starts every time. Have less clatter then before therefore I may need another internal part, will investigate at a later time.
Did you find this story helpful?
Thank you for voting!
Some clipper blades would pull hair that means the lever is bad.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
