It is constructed with tough, thick outer rubber insulation for a long service life.
Power Cord Specifications:
• 2 Prongs
• 2 Wires
• 14 Gauge
• 10 Feet Long
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Perfect
Works like new. Install was easy (followed a YouTube video). This part does not ship with the wire terminals that are on the factory part. I didn't use any, just wrapped the wire and it works great but ring terminals would have made for a clean factory like repair.
Guest - April 25, 2019
Verified Purchase
★★★★★
★★★★★
cord
just what I needed
Guest - June 5, 2019
Verified Purchase
★★★★★
★★★★★
Quick and easy to do
Product arrived pretty quick. It was a easy repair and took very little time to complete. Parts selection is pretty extensive.
Guest - June 25, 2019
Verified Purchase
★★★★★
★★★★★
Simple Repair
I’ve had my Dewalt miter saw for 15 years and the cord had seen better days. Ordering was simple and the repair was just as simple. I did had to stop at the hardware store for one connector which was .29 cents. Better then buying a new one!
Guest - July 18, 2019
Verified Purchase
★★★★★
★★★★★
power cord
as always, perfect fit. thanks again for getting it RIGHT.
Guest - November 20, 2019
Verified Purchase
★★★★★
★★★★★
Very happy
Arrived ahead of schedule. Will definitely recommend and use again in the future
Max - July 27, 2020
Verified Purchase
★★★★★
★★★★★
Easy and complete
Came quickly and my saw looks and works great
Michael - July 30, 2020
Verified Purchase
★★★★★
★★★★★
good
Good service, great price .
Guest - September 22, 2020
Verified Purchase
★★★★★
★★★★★
Better than oe
Very good parts. Easy to find part and order. Comes in reasonable time frame
Guest - September 29, 2020
Verified Purchase
★★★★★
★★★★★
Great quality
I have a real old DeWalt chop saw. And it did a new cord and had a broken handle ordered both from the replacement parts that came in they fit perfectly and now my saw is like brand new again.
Scott - January 28, 2023
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Remove the handle cover
Make a wiring diagram
Remove the wires from the switch
Remove the cord relief from the old cord and put in on the new cord
Connect the cord wires to the switch
Connect the motor wires to the switch
Screw on the handle cover
Remove the handle cover
Remove the screw holding the switch
Remove the cord clamp
Remove the cord from the switch
Put the new cord protector on the new cord
Cut and strip the cord leads to length, attach terminals
Install the parts in reverse order
Took out all handle screws to remove top from bottom handle. Strip new cord wires, crimp quick connect to switch wire and slide on to switch, wire nut other line, put handle back together, plug in, test switch to run, finished.
1. Removed Torx screws securing saw handle cover to access power cord terminations.
2. Disconnected spade connector on power cord white wire termination.
3. Removed screw lug on switch to disconnect power cord black wire termination.
4. Removed strain relief, cord mounting clamp and damaged power cord and from saw.
... Read more>5. Stripped new power cord outer jacket insulation and cut black and white wires to lengths matching original cord and installed strain relief and mounting clamp on new power cord.
6.Stripped white wire and installed male crimp spade terminal.
7. Stripped black wire and installed crimp screw terminal.
8. Connected white wire spade connecter and black wire to switch screw lug connector.
9. Routed wires to match original installation.
10. Secured strain relief and cord mounting clamp to saw.
11. Installed saw handle access cover and secured with Torx screws.
12. Tested saw operation.
Removed the screws from the switch handle
Removed the cord clamp
Removed the cord from the switch
Slid the cord relief from the old cord and slid it on the new cord
Connected the new cord to the switch
Screwed in the cord clamp
Assembled the switch handle
Did you find this story helpful?
Thank you for voting!
Cord had been cut so many times, strain relief was worn out
Removed side handle half, removed old cord, crimped new connectors on new cord, threaded cord through strain relief, reattached to switch, put handle half back on, put in screws.
1. Separate the handle and take out the old cord.
2. Wire up the new cord and reinstall the handle.
3. Remove the brush caps, install the new brushes and put the caps back on.
Removed top portion of palm sander. Disconnected the black and white wires from motor. Slipped strain reliever over new cord and placed strain reliever into slot in top of sander. Connected white and black wires to same on motor and covered with wire nuts. Screwed top back on. About a ten minute job.
I unscrewed the handle. Then unscrewed the power cord housing. Disconnected the black and white wires and replaced the power cord. Connected the black and white wires and screwed the housing and handle back up.
Remove the handle from the saw
Remove the cord clamp
Remove the cord wires from the switch
Connect the new cord wires to the switch
Screw the cord clamp in
Install the handle
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10169913
Manufacturer Part Number: 330079-98
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
