This is a genuine manufacturer approved replacement starter pulley. It is specially designed for use with gas powered chainsaws. This recoil starter pulley is made out of plastic and it is sold individually. Please note, housing, spring, rope, starter grip and screws are all sold separately. To complete this repair you will need a screwdriver. • Remove the starter housing screws • Separate the housing • Remove old pulley • Secure the new one in place • Reassemble and test the saw
Troubleshooting
This part works with the following brands:
Husqvarna
Poulan
Jonsered
Craftsman
This part works with the following products:
Chainsaw
Part# 530057890 replaces these:
530057890,
Videos For installing this part.
?
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(5 Reviews)
Click to filter by ratings:
5 stars
5
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
wrong part
I ordered the wrong part, your people made it extremely easy to correct my mistake and reorder the correct part. Got it! Thanks to all who helped
Guest - May 21, 2019
Verified Purchase
★★★★★
★★★★★
Works great!
Replaced the spring as well. Had a little trouble with the spring, but that’s because I have bad eye sight, couldn’t see to get the hooked end of the spring into the slot of the housing and the spring came unwound, yikes! I was able to use the pulley to recoil the spring and put the plastic band that the spring was in back on with help from my daughter and managed to get it on the second time. Yay!
Joseph - April 26, 2021
Verified Purchase
★★★★★
★★★★★
Easy repair, great part! Just as expected!
The part arrived quickly and fit perfectly! My chainsaw works like new again! Thanks eReplacementparts!
Brad - December 21, 2021
Verified Purchase
★★★★★
★★★★★
great
the part was correct and fit my chainsaw and was on time
Guest - May 31, 2022
Verified Purchase
★★★★★
★★★★★
Outstanding 2 thumbs up!!
Great part!! Excellent service!
Craig - March 30, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Easy
15 - 30 mins
(4 rated repairs)?
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
The old starter rope pulley was broken, the return spring was unwound, the old starter rope was badly frayed and too short, and the starter handle had been replaced with a big plastic wingnut that is
Remove the engine cover, THEN remove the starter housing and cover.
Remove and discard the old starter rope, wingnut handle, and pulley.
Attach the new starter rope to the new pulley and thread it through the
correct hole in the starter housing while maintaining the proper orientation
between the pulley and the h
... Read moreousing.
Rewind the return spring until it fits in the space for it in the starter housing.
Hold the return spring in place, compressed, while sliding the pulley into
place so the notch in the pulley engages the spring.
Pull the starter rope and let the pulley rewind while sliding the starter assembly
into place so the pawls in the flywheel engage the notches in the pulley.
Replace screws in starter housing and tighten lightly.
Test starter operation.
If starter engages and disengages properly, tighten screws.
If not, realign starter housing and test operation again.
Install engine cover and tighten screws.
Read less
Did you find this story helpful?
Thank you for voting!
Accidentally ran over chainsaw with bobcat and replace parts that was damage
Watch ereplacementparts on youtube on how to install spring-starter was helpful. I could be wrong but couldn\'t find and order other decals for side the of housing-fan (poulan model P3816) and rear of shield-cylinder (instruction on how to start and stop chainsaw).
Removed starter cover and loosened rope, removed pulley, removed old winder spring, reversed process to install. I was very careful while installing the spring, pushed I it into position slowly so that the wire holding it tight slid off without uncoiling the spring rapidly. They include gloves in the repair kit, which you should us.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9004620
Manufacturer Part Number: 530057890
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_11.gif "Part Location Diagram of 530057890 Husqvarna Pulley")
_WW_11.gif "Part Location Diagram of 530057890 Husqvarna Pulley")
