Part Location Diagram of 530039238 Husqvarna Module - Ignition
See part A-4 in the diagram
( Grid squares measure 1x1 inch )

Module - Ignition 530039238

Manufactured by:
Husqvarna
ERP Number:
ERP16352512
Part Number:
530039238
Original Equipment Manufacturer ?
$90.40
On Order

Easy 

Less than 15 mins 

(1 rated repair) ?

Does this part fit my model?

Need help finding your model number?

Product Description

?

This is a genuine replacement part that is sourced from the original manufacturer to be used with chainsaws from Craftsman. The ignition module attaches to the motor assembly near the flywheel. This part is used to create an electric charge when the magnets on the side of the flywheel pass the ignition module. Replacing this part may be recommended when the engine has compression but will not start or will not stay running. The ignition module is sold individually.

Troubleshooting

This part works with the following brands:
  • Craftsman
  • Poulan
  • Husqvarna
  • Jonsered
This part works with the following products:
  • Chainsaw
Part# 530039238 replaces these:
530039238,

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

Less than 15 mins 

(1 rated repair) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

The chainsaw I would not start very well when it did it was like a misfire

Rod from Claremont, New Hampshire

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
530039238
Initially I started my repair by a good clean up of the chainsaw. I used a torx bit to remove the ignition module wipe down the flywheel and placed in the new ignition module. Before tightening down the torques screws I slid a business card between the flywheel magnet and the ignition module to set the correct air gap. Finish tightening u p the torque screws. Reinstalled rope starter cover. Gave it a few pulls and it started right up. I want to thank you guys so much.

Rod
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP16352512
Manufacturer Part Number: 530039238
Brand Model Number Description
Craftsman 358350670 Chainsaw - Chainsaw
Craftsman 358350671 Chainsaw - Chainsaw
Craftsman 358350810 Chainsaw - Chainsaw
Craftsman 358350811 Chainsaw - Chainsaw
Craftsman 358350830 Chainsaw - Chainsaw
Craftsman 358350870 Chainsaw - Chainsaw
Craftsman 358351600 Chainsaw - Chainsaw
Craftsman 358351610 Chainsaw - Chainsaw
Craftsman 358351800 Chainsaw - Chainsaw
Craftsman 358351810 Chainsaw - Chainsaw
Craftsman 358360360 Chainsaw - Chainsaw
Craftsman 358360361 Chainsaw - Chainsaw
Craftsman 358360380 Chainsaw - Chainsaw
Craftsman 358360381 Chainsaw - Chainsaw
Craftsman 358360680 Chainsaw - Chainsaw
Craftsman 358360681 Chainsaw - Chainsaw
Jonsered CS2138 Chainsaw - Chain Saw
Poulan PP3816 Chainsaw - Gas Chainsaw
Poulan PP4218 Chainsaw - Gas Saw
Poulan PPB4018 Chainsaw - Gas Chainsaw
Poulan PPB4218 Chainsaw - Chain Saw
Poulan PR4218 Chainsaw - Gas Chainsaw