This band saw wheel tire is designed to fit 18-inch band saw wheels, providing reliable traction and stable support for the blade during operation. Its durable rubber construction helps maintain proper blade tracking while reducing vibration and operating noise for smoother, more accurate cuts. Replacing a worn, cracked, or hardened tire restores consistent blade alignment, improves cutting performance, and helps ensure safe, dependable operation. The tire can be installed on either the upper or lower wheel and is an essential wear item for maintaining optimal saw performance over time.
Troubleshooting
This part works with the following brands:
Jet
Powermatic
This part works with the following products:
Band Saw
Table Saw
Part# JT9-JWBS18DX-133 replaces these:
JWBS18DX-133,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(12 Reviews)
Click to filter by ratings:
5 stars
12
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
2
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Worked better than I hoped
New tires for my bandsaw work very well.
Guest - April 28, 2019
Verified Purchase
★★★★★
★★★★★
Correct replacement part!
Worked great as a replacement part for the JWBS 18x-3 Jet band saw.
Guest - June 22, 2019
Verified Purchase
★★★★★
★★★★★
The tire is high quality but is a little pricey after you add on the other charges
I was shut down for one week waiting for the part. The tire is excellent
Russell - June 29, 2019
Verified Purchase
★★★★★
★★★★★
Worked perfectly.
The part was a perfect fit.
Guest - February 10, 2020
Verified Purchase
★★★★★
★★★★★
Perfect replacement
Product arrived promptly. Good factory replacement
Mark - March 23, 2020
Verified Purchase
★★★★★
★★★★★
When when I know my part or where it is on a diagram your site is perfect. Quick and easy.
I actually like the replacement part better than the original. They are flatter and seem to run truer.
Guest - August 15, 2021
Verified Purchase
★★★★★
★★★★★
Great Tires, not so easy to install. But I knew that!
These tires are great. They were difficult to install, but I knew that going into the repair. There are several online recommendations for installation. Heating the tire with hot water helped. I look forward to repurchasing these for my other bandsaw.
Jonathan - September 15, 2021
Verified Purchase
★★★★★
★★★★★
A challenge to place on bandsaw wheels.
I was given top drawer service by EReplacement staff. Came soon and was right part. But boy was it hard fitting it on wheel. I heated it up though and finally got it on with screwdrivers and 3 visegrips to hold in place the sections already on wheel.
Scott - January 11, 2022
Verified Purchase
★★★★★
★★★★★
Exact part
Perfect OEM part and shipping was fast-
Guest - September 11, 2022
Verified Purchase
★★★★★
★★★★★
Awesome
Perfect fit, works great
Guest - January 6, 2023
Verified Purchase
< Prev
1
2
Next >
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
A Bit Difficult
30 - 60 mins
(27 rated repairs)?
< Prev
1
2
3
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
I boiled a pot of water. I put 1 tire in the boiling water, took the pot off the stove and then let the tire sit in the water for 5 minutes while it was off the stove. I then took it out of the water, dried it off. I clamped the tire to the wheel with a C clamp and put a small piece of scrap wood between the clamp and the tire so I wo
... Read moreuldn\'t damage it. With one side of the tire clamped to the wheel, I went around the wheel with a large screw driver stretching the tire onto the wheel. It fits really tight and like I read in other posts, I thought I had the wrong size tires sent to me at first. If you cant stretch the tires enough to get them on the wheel, just put them in boiling water longer.
The tire has to be stretched over the wheel, takes time to do it by yourself, clamp in one place and then work it around stretching with pry bar and screw drivers....
1. Removed bandsaw wheel from bandsaw.
2. Removed old tire and cleaned wheel of any stuck pieces.
3. Using spring clamps, an extra set of hands and a flat nosed screwdriver mounted new tire in much the same way a bicycle tire is mounted to its rim. Prying actions and clamping or holding the tire in its new position until anot
... Read moreher bite could be made.
4. Tire is tough so it is not easy to install but two of us got it on in about 4 minutes.
5. Center tire properly on wheel.
6. Reinstall newly tired bandsaw wheel and test it with the blade properly installed.
7. My new tire did not change any of the tracking settings on my bandsaw. Good Luck
The tire that is now available from any source is made from ? It is white in color and doesn\'t stretch easily and then only a little bit. I broke the first belt when I tried to pre stretch it. I ordered a second belt from a different source but it was the same belt. Ugh!
I watched a lot of You Tube videos but they all used a belt
... Read morethat stretched more so it was an easy job. Heating the belt in water didn\'t help me at all.
I heated the belt in an oven to 400 degrees F. I wore thick leather gloves to handle it.
I clamped as much of the belt as possible to the rim and then used two philips screw drivers to pry the belt over the wheel on my bench. When you get two screw drivers about 6\" apart with the belt halfway on the wheel you can pound on the top of the screwdriver handle to get the belt all the way on the wheel. A helper would probably be a benefit. I used the flat side of a wood chisel to center the tire by pounding the other side of the chisel with a hard mallet.
I soaked the new tires in hot water for a while to make them more pliable. I removed the old tires. Then with the help of a neighbor, we stretched the new tires on. Adjusted the tracking. It\'s working great now.
Did you find this story helpful?
Thank you for voting!
Tire on lower wheel of 18\" band saw needed to be replaced
Had a friend come over
Warmed the tire in hot water
Clamped the tire to wheel
I held the wheel and slowly rotated it
Friend used 2 screw drivers to stretch tire onto wheel
Not a one man job.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
