Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Easy replacement on saw
As good or better than original part
Guest - December 14, 2021
Verified Purchase
★★★★★
★★★★★
Easy repair
The part arrived sooner than expected and was packaged well. The actual job of replacement went smoothly. With the new shaft hinge assy in place and adjusted the saw ran like new. Very happy with replacementparts.com - saved over a thousand $$ with a small investment and a little time.
Guest - December 21, 2021
Verified Purchase
★★★★★
★★★★★
This part was lost in shipping.
The person that i spoke with was so helpful and understanding that we will always shop with a company that take our business seriously. Thank again for your quick response in resolving the issue.
Guest - February 13, 2023
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
A Bit Difficult
30 - 60 mins
(3 rated repairs)?
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
1 Unplug bandsaw
2 Remove blade
3 Remove left blade guard (2 screws)
4 Remove upper door retainer
5 Remove upper blade cover assy (2 screws)
6 Remove blade tension screw (don\'t loose nut and spring)
7 Flip tension bar out of way and lift hinge shaft assy up and out
8 Loosen hinge angle adjustment
... Read more setscrew
9 Remove hinge pins (may require drilling a small hole in each, and using small sheet-metal screw to pull)
10 Press new wheel shaft into hinge plate from wheel side of plate (must be straight or wheel adjustment bushing won\'t thread in)
11 Remove wheel adjustment bushing from old hinge plate
12 Install wheel adjustment bushing to same depth as original setting (be careful not to cross thread - it\'s easy to damage the threads)
13 Drill through top of hinge plate into shaft for retention pin (oops, needed new pin - you can\'t do this after assy)
14 Put hinge plate in position and press pins in place
15 Reinstall hinge plate assy onto saw
16 Flip tension device into place and install tension screw, spring and nut
17 Reinstall upper wheel cover and left blade guard and any other housing components
18 Install upper wheel - bearing nut should not be over tightened - proper tension is snug, with no additional drag on bearings (spin the wheel while tightening to verify)
19 Install and adjust blade tracking - low tension with guides out of the way
20 Check that the upper and lower wheel are co-planar by viewing from right side of machine - this affects blade tracking match of upper and lower wheels
21 Adjust planetary, if needed (must remove blade and upper wheel to access front and rear setscrews on hinge plate pin)
22 Reassemble, adjust blade tracking and recheck planetary as needed
23 Adjust blade guides
24 Close covers
24 Plug in
25 Try it
The hardest part was getting the hinge out of the support housing. Had to drill the old hinge to get the pins out then it was just matter of putting it back together. If you don\'t have a press it maybe a bit tricky to hammer the wheel that into the hinge
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP19159510
Manufacturer Part Number: JT9-JWBS14DP-49
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_1.gif "Part Location Diagram of JT9-JWBS14DP-49 Jet SHAFT HINGE ASSY")
_WW_1.gif "Part Location Diagram of JT9-JWBS14DP-49 Jet SHAFT HINGE ASSY")
